2006 Johnson 15hp outboard compression test #nashville #tennessee #johnson
Hawkeye Marine Doing a compression test on a 2006 Johnson 15hp outboard.
Thanks for watching!
#nashville
#tennessee
#johnson
46
views
1957-1960 Johnson 18hp carburator repair #nashville #tennessee #johnson
Hawkeye Marine Doing a service on an old Johnson 20hp Outboard. This motor would be between 1957-1960 FD-21R. Put a new choke lever on it.
Thanks for watching!
#nashville
#percypriestlake
#tennesee
53
views
1980's Suzuki DT150 150hp lower unit removal #nashville #percypriestlake #suzuki
1986 - 1989 Suzuki DT150 150hp outboard lower unit removal.
Thanks for watching
#nashville
#percypriestlake
#suzuki
34
views
1967 Mercury 950 95hp revisit carbs and rectifier #nashville #percypriestlake #oldhickorylake
Hawkeye Marine just revisiting this 1967 Mercury 950 95hp outboard. I took the top carb off. Which seemed like it had and issue with it. I discovered it had some blockage in the bottom jet. It also had a small hairline crack in the emulsion tube. I had one of those and replaced.
The battery was on a charger and I checked the output of the rectifier. It was swinging wildy in voltage so, I think we have a bad rectifier. I have order a couple of those.
I also revisited the fuel pumps. I now have the pumps working and its pressurizing good.
Thanks for watching
#nashville
#percypriestlake
#oldhickory
56
views
Mercury 9 9hp service first look #nashville #percypriestlake #mercury9.9hp
I have a Mercury 9.9hp mid-90's outboard. It came to me from a friend that asked me to service it and sell it for him. It came off a run-about as a kicker motor for the boat. He took the motor, controls and wiring harness off the boat and brought to me. I run through it an discovered the shift is not working and seems to be bound up in the motor. The lower unit was fine but, where it was bound up was in the shifting mechanism on the motor.
Thanks for watching!
#nashville
#percypriestlake
#mercury9.9hp
31
views
Suzuki Outboard DT150 service part 1 #nashville #percypriestlake #suzuki
Doing a service on a Suzuki Outboard DT150 engine. Customer tried to replace the thermostat and broke two of the thermostat bolts off in the head.
#nashville
#percypriestlake
#willitrun
39
views
Johnson Evinrude checking the ignition system
Just mulling around have a couple of Johnson Evinrude motors that I need to check the igniton systems on.
Thanks for watching!
#nashville
#percypriestlake
#willitrun
19
views
April 25, 2020 Big Bass Day on Percy Priest Lake in Nashville
April 25, 2020 Big Bass Day on Percy Priest Lake in Nashville. Thought I would post a catch from last year. Really nice catch.
Thanks for watching!
#nashville
#percypriestlake
#bigbass
33
views
Snowpocalype 2022
We got 5 inches of snow. Working in the garage
Thanks for watching!
#nashville
#snowpocalype
#garage
93
views
Mercury Distributors
Hey thanks to everyone who has subscribed to my channel. Mr. Airsoft asked a question about his distributor. So, I pull out a couple of distributors that I have. Basically just talk about the differences. Hope this helps.
49
views
Mercury 850 85hp smart people being stupid
I have a couple of Mercury 850 85hp engines Larry brought me. One of them is locked up and the other one is not. I chose to start with the one locked up. I got it freed up and do a compression test. I hope you enjoy.
Thanks for watching.
#percypriestlake
#nashville
#willitrun
54
views
1967 Mercury Thunderbolt 950 95 hp engine fuel pumps rebuild part 8
Doing a service on a 1967 Mercury Thunderbolt 950 95hp outboard motor. A fellow Youtuber brought me this engine to see if I can get it to run. Its a pretty rare engine. I've not seen one of these before.
In this episode I rebuild the fuel pumps. It has two fuel pumps so I had to figure out how the fuel deliver system works. Normally you just have one fuel pump to deal with. This one has two fuel pumps. Thanks for watching!
#Nashville
#PercyPriestLake
#wilitrun
48
views
2015 Bayliner with a Mercruiser 3.0 engine service
Doing a service on a 2015 Bayliner with a Mercruiser 3.0. Repaired the shift linkage. It was not engaging the two switches to momentarily die the engine to shift into gear.
Thanks for watching!
#percypriestlake
#Nashville
#bayliner
33
views
1967 Mercury Thunderbolt 950 95 hp engine wiring harness part 7
Doing a service on a 1967 Mercury Thunderbolt 950 95hp outboard motor. A fellow Youtuber brought me this engine to see if I can get it to run. Its a pretty rare engine. I've not seen one of these before.
In this episode I install the new engine harness. I had to get a little creative to get the new harness to mount correctly on the engine. Thanks for watching!
#Nashville
#PercyPriestLake
#wilitrun
13
views
1970's Mercury hydraulic tilt and trim bleeding the system
Testing and bleeding an old 1970's hydraulic tilt and trim system. Hope you enjoy. Thanks for watching!
9
views
Mercury 25 hp tracker boat hits a rock see the damage
A customer with this 1999 Tracker with a Mercury 25hp hit a rock. Percy Priest Lake has lots a rock. Guy hit rock constantly on that lake. If you go look at Performance Proppeller James has a Percy Priest Lake wall of shame. He torqued the lower unit so badly that it literally bent the shaft.
Thanks for watching!
#PercyPriestLake
#Nashville
#willitrun
49
views
1967 Mercury Thunderbolt 950 95 hp Distributor Rebuild part 6
Doing a service on a 1967 Mercury Thunderbolt 950 95hp outboard motor. A fellow Youtuber brought me this engine to see if I can get it to run. Its a pretty rare engine. I've not seen one of these before.
In this episode I rebuild the distributor by adding some new wiring. Thanks watching!
#Nashville
#PercyPriestLake
#wilitrun
25
views
1999 Champion Mercury 200 EFI FINAL
We took it for a test drive and a little fishing.
My uncle Scotty bought this 1999 Champion 191 with a Mercury 200hp EFI outboard on it. It was basically a barn find. It had been sitting for a couple of years. He asked me to go through it and do a good run through on it and get it ready for the lake.
I love these old Champions. I think they are the best built Bass Boats ever made. In this episode we took it for a test ride. Hope you enjoy!
Thanks for watching!
#PercyPriestLake
#Nashville
#willitrum
32
views
2
comments
1999 Champion Mercury 200 EFI New jackplate install part9
My uncle Scotty bought this 1999 Champion 191 with a Mercury 200hp EFI outboard on it. It was basically a barn find. It had been sitting for a couple of years. He asked me to go through it and do a good run through on it and get it ready for the lake.
I love these old Champions. I think they are the best built Bass Boats ever made. In this episode we replace the RiteHite jackplate with a Vance Manufacturing jackplate. Hope you enjoy!
Thanks for watching!
#PercyPriestLake
#Nashville
#willitrum
17
views
1999 Champion Mercury 200 EFI WE GOT A LEAK part8
My uncle Scotty bought this 1999 Champion 191 with a Mercury 200hp EFI outboard on it. It was basically a barn find. It had been sitting for a couple of years. He asked me to go through it and do a good run through on it and get it ready for the lake.
I love these old Champions. I think they are the best built Bass Boats ever made. In this episode I found one of the pump was leaking. I replaced the hydroair pump and the bilge pump with new cartridges.
Thanks for watching!
#PercyPriestLake
#Nashville
#willitrum
32
views
1999 Champion Mercury 200 EFI Water Pump replacement part7
My uncle Scotty bought this 1999 Champion 191 with a Mercury 200hp EFI outboard on it. It was basically a barn find. It had been sitting for a couple of years. He asked me to go through it and do a good run through on it and get it ready for the lake.
I love these old Champions. I think they are the best built Bass Boats ever made. In this episode I replace the water pump.
Thanks for watching!
#PercyPriestLake
#Nashville
#willitrum
29
views
1999 Champion Mercury 200 EFI Lower unit removal part6
My uncle Scotty bought this 1999 Champion 191 with a Mercury 200hp EFI outboard on it. It was basically a barn find. It had been sitting for a couple of years. He asked me to go through it and do a good run through on it and get it ready for the lake.
I love these old Champions. I think they are the best built Bass Boats ever made. In this episode I remove the lower unit.
Thanks for watching!
#PercyPriestLake
#Nashville
#willitrum
51
views
1999 Champion Mercury 200 EFI Thermostat replacement part5
My uncle Scotty bought this 1999 Champion 191 with a Mercury 200hp EFI outboard on it. It was basically a barn find. It had been sitting for a couple of years. He asked me to go through it and do a good run through on it and get it ready for the lake.
I love these old Champions. I think they are the best built Bass Boats ever made. In this episode I replace both Thermostats.
Thanks for watching!
#PercyPriestLake
#Nashville
#willitrum
20
views
1999 Champion Mercury 200 EFI compression test part4
My uncle Scotty bought this 1999 Champion 191 with a Mercury 200hp EFI outboard on it. It was basically a barn find. It had been sitting for a couple of years. He asked me to go through it and do a good run through on it and get it ready for the lake.
I love these old Champions. I think they are the best built Bass Boats ever made. In this episode I do a compression test.
Thanks for watching!
#PercyPriestLake
#Nashville
#willitrum
56
views
1999 Champion Mercury 200 EFI tilt and trim part3
My uncle Scotty bought this 1999 Champion 191 with a Mercury 200hp EFI outboard on it. It was basically a barn find. It had been sitting for a couple of years. He asked me to go through it and do a good run through on it and get it ready for the lake.
I love these old Champions. I think they are the best built Bass Boats ever made. In this episode I inspect and fill up the power tilt and trim fluid.
Thanks for watching!
#PercyPriestLake
#Nashville
#willitrum
29
views