Fred's Left Hand Part 12

Fred's Left Hand Part 12

When you think of a hand, you tend to look at from the tips of the fingers back to the wrist.
But in the human hand, most of the muscles that drive the fingers are located in the forearm.
This is the same with the Inmoov robot.
So our journey we will start with the forearm.
This is convenient as I already have Fred's arm built down to his elbow on the left side.

In Part 1, I decided to use PTEG. For the forearm, most of it is a standard build except for the modified wrist.
In Part 2, I used a few nutserts and installed the servos.
In Part 3, I started on the version 2 hand its self.
In part 4, I installed the 5 Hall sensors and the springs.
In Part 5, I installed the electronics and the PTFE tube
In Part 6, I installed and wired the PCA9685.
In Part 7, I add the Elbow gear and connect all the tendos to the servos.
In Part 8, I test out the MPU6050 and the finger sensors.
In Part 9, I mount the bicep servo and 20A SMPS to the back of the Bicep.
In Part 10, I connect the forearm to the bicep and setup the pot and bicep servo, testing the joint with a servo tester.
In Part 11, I attached the assembled arm to the shoulder on Fred.

In Part 12, I wire up a board with terminals to connect the various feeds to the TCA9548A I2C Multiplexer.

Link to the Calibrator part: http://inmoov.fr/wp-content/uploads/2019/01/Calibrator.stl
20A SMPS Mount: https://github.com/Cyber-One/Fred_Inmoov/blob/main/Parts/20A_SMPS_Mount_V2.stl

Way back in September 2021 I started the Left shoulder project
Part 1: https://youtu.be/gukMttyD0S0
Part 2: https://youtu.be/QraGu_SuFdU
Part 3: https://youtu.be/jT1FCTPzgCU
Part 4: https://youtu.be/Mljajffq-38
Part 5: https://youtu.be/ErPONNBTs78

The PTFE tube are 1.5mm ID and 2.5mm OD with the following lengths:
Thumb 335mm
Index 300mm
Middle 300mm
Ring 300mm
Pinky 360mm

The 12 core ribbon wire used has the following wire assignments
1 - Servo Power - 6V
2 - Servo Power - 6V
3 - Servo Power - 6V
4 - I2C VCC - This is the I2C Bus power 5V
5 - I2C SDA - Serial Data
6 - I2C SCL - Serial Clock
7 - I2C Output Enable - Not Yet Used
8 - I2C Gnd
9 - Spare conductor for secondary I2C VCC
10 - Servo Gnd
11 - Servo Gnd
12 - Servo Gnd

The Spare I2C VCC on wire 9 is planning for the future.
The MPR121 is a capacitive touch sensor that would add to the ability of the hand to sense its environment, however it's max power supply is 3.5V, well below the Hall senors 4.5V minimum.
When MRL supports this chip, we can supply it with 3.3V and use the same SCL, SDA and Grd wires.
Up to 4 of these devices can be on the same I2C bus.

Please Like, Subscribe and ring the notification bell to be alerted when the next video is released.
It also a form of support that costs you nothing, but does help the channel a lot.

Also please consider joining my VIP Patreon's GoLucky and Louwrens Burger and my Builder Patreon's Lmorales45 in supporting the channel on Patreon.
https://www.patreon.com/Cyber_One
Builder level Patreons get the videos 2 weeks before YouTube does,
VIP Patreons get the videos as they are created, from 2 weeks to 2 months before YouTube.

Alternatively you can help with a donation via PayPal
https://www.paypal.com/donate/?hosted_button_id=T6NBDSZQXJ8RC

Maybe drop into the discord server for a chat :-)
https://discord.gg/WzrBUTkthQ

I have a number of Play-Lists that may also interest you:
Spot Micro build using MRL
https://youtube.com/playlist?list=PLgXTfFM40HqF6YqVjWtEtDC-ekbIkpkyE
Fred's modified Inmoov Robot Head created in the Fred's Head Series.
https://www.youtube.com/playlist?list=PLgXTfFM40HqEbnFfhaLPmLv_RS1ZRCilI
Fred's Head, a better stand. (This series)
https://youtube.com/playlist?list=PLgXTfFM40HqHV5EPKPULJDfbuXK1KUeeS
The Inmoov Walking Robot Series.
https://youtube.com/playlist?list=PLgXTfFM40HqEMwg9rJ078INRYWDCG66B3
Fred's Static Leg build and attach series, now finished.
https://youtube.com/playlist?list=PLgXTfFM40HqHhaHpmX4HQO9xJAz-pAsOm
The Creality CR10S5 3D Printer Series.
https://youtube.com/playlist?list=PLgXTfFM40HqH2fJ3Wsu2wX90h1_V4uI5n
The Cocoon Create Touch 3D Printer Series.
https://youtube.com/playlist?list=PLgXTfFM40HqHJlvRuSbhYUvdWBraW9tri
My Industrial videos.
https://youtube.com/playlist?list=PLgXTfFM40HqFNvDBGjblVrEkl3jrQKMDE
And finally some of my unboxing videos.
https://youtube.com/playlist?list=PLgXTfFM40HqFXHXRLBa9tsLhRQGcORZQO

See you in the next video :-).