TheWayIDidIt

How I insulated and add a USB power port to my ST1300

A short ride through the Mountains on NC

a little info I use to change spark plugs in a 2007 ST1300

A step-by-step description of how I installed the step stabilizer/support on my RV's folding steps

A brief description of the repair made to my camshaft position sensor for my 2008 F350 6.4L dually

A step-by-step description of how I installed the Stealth module in my fully stock, dual alternator equipped 2008 F350 6.4L Dually

A step-by-step description of how I replaced the oil pan gasket on my 2012 VW Beetle

A brief description of an ice maker I used in my RV

A step-by-step description of how I changes the front brake pads and rotors in my 2017 MDX advance

A description of the the process I use to grease the slide pins of my F350 dually

A short description of the process I used to replace the tail/back-up light holder on a Bobcat 773 skid steer. An easy task but I thought I'd share anyway :)

A description of how I corrected the improper hanging of my Shower door. This included the removing of the wall and door. After relocating the hinge point, I reinstalled the walls and door. As always, this video is for those that can't, or don't want to, pay someone to do what they can do themselves with minimal guidance. Time Stamps: Problem description: 0:09 Panel removal: 3:35 Hinge hole relocation: 7:25 Seal install: 8:00 Panel Install: 8:30

Step-by-step description of how I replaced the brake switch B on the master cylinder of my 2008 F350 6.4L to get the cruise control working.

This is a description of what I did to remove the hydraulic valve and prepare the 453 for the reinstall action of the valve. the remove portion of the video is about 15 min. I tried to make the video move slow enough to be able to see what was happening but not so slow it lasted forever. I also provided any tips that help me get the valve out. See the timestamps below to help navigate the video: 0:45. steering linkage 1:35 start on hoses 1:55 center panel removal 7:25 links and pins 10:00 bracket and bolts 14:30 hydraulic valve bolts 15:00 valve removal 15:35 valve mounting bracket 16:09 453 before cleaning 16:54 453 after cleaning 17:40 cleaning the valve 17:50 clean valve with valve numbers 18:22 documentation overview/parts list

Pointing out all the grease points of a Bobcat 453

Beetle Oil Change 2012 Step-by-step instruction on how to change the oil in a 2012 VW Beetle

After several shooting sessions, its time for a review Amazon link: https://www.amazon.com/Pinty-3-9x32EG-Rangefinder-Illuminated-Reticle/dp/B01NBRI1DP Date: 01june2020

A step-by-step description of what I did to repair the cupholders in my 2012 VW Beetle. This includes removing the front seats, the middle console, the gear shift knob, and the climate control module. I have purposely kept all task in this video even though it's a bit long. See below for each task by time stamp; Problem description: 0:26 Battery disconnect/reconnect: 1:00 / 31:45 Front seat remove/install: 1:28 / 28:10 Center Console remove/install: 4:30 / 15:45 Gearshift Knob remove/install: 7:00 / 25:00 (ends at 27:05) Climate control console remove/install: 9:50 / 19:40 (ends at 23:25) Cupholder repair: 13:30

This is a step-by-step description of the process I used to change the battery in the Roomba S9+ 9550 robot. it's really easy. As always, my videos are for those that, with a little guidance, can perform a task that they can't, or don't want to, pay someone else to do.

This is a step by step description of the process I used to give a flagpole new life and installing the EKEV flagpole kit. The kit appears to be a decent one. As always, my videos are for those that, with a little guidance, can perform a task that they can't, or don't want to, pay someone else to do.

This is a step-by-step description of the process of I followed to install 6 Halo down lights. This includes allowing for the roof trusses, detecting the trusses with a stud finder, wiring and mounting the lighting hardware. My videos are for those that cant, or don't want to, afford to pay someone to do something they can do themselves, with a minimal amount of guidance. Mapping and Location prep..... 00:22 An overview of the product..... 07:16 Wiring of the product................. 09:35 The finished product................... 12:03

step by step instruction on how to add head & tail lights to a DS ClubCar see my other video, "adding a 6 in lift" to the cart to learn how to determine the year and make of your cart.

Replacing your car's interior lights with LEDS. This is my 2005 Honda Accord.

Had an old grill that I gave new life.

Too much water in the crawl space spurs the installation of a drainage system. The system has 2 drain boxes, 2 down spout connections, an outlet port, and a stubbed in drain for later use. The cause of the problem was 2 fold. The first was that the water from the downspouts was not evacuated quickly enough and the second was that the drain pipes under the sidewalk were rapidly being over grown and clogged by grass.