Voron 2.4 - E6 - Gantry Mounting & Belt Routing
This week on the Voron build, it's time to get the gantry on and the belts routed, it's getting very close to time to put the electronics on. Then all that's left is the wiring. Rumble Link: https://rumble.com/c/c-606387 Discord Link: https://discord.gg/Dzke8e6
56
views
Voron V2.4 - E5 - Afterburner
This week it's time to build and install the Afterburner toolhead on the Voron V2.4 Discord Link: https://discord.gg/Dzke8e6
67
views
Voron 2.4 - E4 - Gantry Crossbar and X Carriage
This week on the Voron 2.4 build we put the Gantry Crossbar together and then it's time to assemble the X Carriage as well. Discord Link: https://discord.gg/Dzke8e6
34
views
Voron V0 Build - E19 - Rebuild and New Parts
This week we wrap up the V0 build with a complete overhaul of the V0 printer, all new printed parts, the addition of the Tophat, and a few little eastereggs too. Discord Link: https://discord.gg/Dzke8e6
21
views
Book Review - The Lost Fleet Series
This week we've got a quick overview of The Lost Fleet Series. It's a slightly different take on the usual Military Sci-Fi, and I think it's well worth the read or the listen. Discord Link: https://discord.gg/Dzke8e6
21
views
Voron 2.4 - E3 - A/B Drive and Idlers
This week we're getting the A/B drive units and the idlers assembled and mounted to the gantry carrier. The Sharp's Arena Discord: Discord Link: https://discord.gg/Dzke8e6
34
views
Book Review - Starship's Mage Red Falcon
A quick little review and teaser of the Side series for Starship's Mage, Starship's Mage Red Falcon, which follows the crew of the Bluejay after the events in Book 1 of the main series Discord Link: https://discord.gg/Dzke8e6
12
views
Voron 2.4 - E2 - Z-axis Motion system
In this week's Voron 2.4 build video we get the Z-drive, Idlers, and rails installed. Discord Link: https://discord.gg/Dzke8e6
31
views
Sharp's Garage - Plans for the WJ
Just a quick overview of what I have in mind for the WJ. I was going to put this up last winter (2020) and start on it in the summer (also 2020) but with everything that happened I didn't have the funds to do everything that I wanted with it and what was needed to do so I could have it this winter. Discord Link: https://discord.gg/Dzke8e6
1
view
Voron V2.4 - E1 - Intro & Frame
The start of the new Voron V2.4 build. Now that the V0 is complete it's time for the 2.4 to start taking shape in this week's episode we start on the frame. Discord Link: https://discord.gg/Dzke8e6
102
views
Voron V0 Build - E18 - First Prints & Serial Request
This week on the Build, it's finally time for printing and for a serial request. (Yes this video is private until it's the correct time in the sequence for it to be released. I just wanted the serial, so I can make parts that include it for the upgrade) Discord Link: https://discord.gg/Dzke8e6
1
view
Book Review - The Extinction Cycle
Just my thoughts on The Extinction Cycle series by Nicholas Sansbury Smith. It's a very interesting series and a good read, I would recommend it if you are tired of the usual zombies but you still want something in the same vein, go give it a listen or a read, and I hope that you enjoy. Discord Link: https://discord.gg/Dzke8e6
52
views
Voron V0 Build - E17 - Temporary Panel Mounting
This week we've reached the end of the build. It's time to add the Poly-carbonate panels to the V0 and get it sealed up for printing. Discord Link: https://discord.gg/Dzke8e6
17
views
Voron V0 Build - E16 - Software and Firmware config
This week it's time for getting the software and firmware setup and configured for the printer. It's not too hard a process, but it does take a little time and there are some pitfalls to avoid as well. Discord Link: https://discord.gg/Dzke8e6
9
views
Book Review - Chronicles of Max [REDACTED]
A quick little review for a series that I've listened to a couple of times and read through once. It's an interesting thought experiment and one that may or may not come to pass, we shall see. I hope that you enjoy, feel free to leave a comment down below, or to hop onto the discord and chat. Discord Link: https://discord.gg/Dzke8e6
1
view
Voron V0 Build - E15 - Toolhead wiring
This week on the build it's time to get the toolhead wired and tied into the control board. We are very close to being able to run this printer. Next up is configuring the software which we will cover next week. I hope to see you then and fell free to hop into the discord and chat. Discord Link: https://discord.gg/Dzke8e6
25
views
Voron V0 Build - E14 - Wiring the Electronics
This week it's time to start getting the electronics wired in, checking the power supply, and making sure that we get everything as tidy as we can. It's a long on, so grab a drink and take a seat to follow along. Discord Link: https://discord.gg/Dzke8e6
55
views
Voron V0 Build - E13 - Electronics Mounting
We're finally getting close to the end. It's time to get the electronics mounting sorted out. This week it's time to get the power supply, control board, buck converter, and Raspberry Pi mounted. Discord Link: https://discord.gg/Dzke8e6
Voron V0 Build - E12 - Final Frame Assembly
This week, it's time to get the last few pieces of the frame assembled, get the last few nuts in the frame for holding the side panels in. And from here it's just a few more parts until it's all finished and we're printing with it. Discord Link: https://discord.gg/Dzke8e6
Starship's Mage review pt 2
In this episode I'm tackling the second four books of the Starship's Mage Series, while trying to not give out too many spoiler's and to attract your attention and curiosity. Especially if you enjoyed the first four books. Discord Link: https://discord.gg/Dzke8e6
1
view
Book Review - Starship's Mage, Pt.1
The intro for my little book/series review series. In this I'm going to try to give a general overview of the book or series in question and a recommendation for it. In this episode I'm tackling the first four books of the Starship's Mage Series, while trying to not give out too many spoiler's and to attract your attention and curiosity. Discord Link: https://discord.gg/Dzke8e6
22
views
Voron V0 Build - E11 - Toolhead assembly
This week it's time to put the toolhead together for the V0. It takes a little work to do, but it's not terribly hard to get it to happen once we get it figured out. You'll want to watch to the end, as there are a few things that I oops in the initial build, and a few things that are just good to know, that I add in at the end. Discord Link: https://discord.gg/Dzke8e6
24
views
Voron V0 Build - E10 - Feet & Belt routing
This week it's time to put the feet on the printer and to put the belts on so we can get one step closer to actually getting this printer printing. Discord Link: https://discord.gg/Dzke8e6
13
views