Racer88videos

Tanabe Medallion Turbo-Back Exhaust. Cobb Stage 2 tune.

Testing a new P80 build for proper cycling of (dummy rounds) ammo - feeding, extraction, and ejection.

Testing a new P80 build for proper cycling of (dummy round) ammo - feeding, extraction, ejection.

An inspirational video mash-up by Racer88.

Colorado Senator Chris Hansen showcases his utter ignorance on building Privately Made Firearms. Or is he intentionally LYING??? And they make LAWS based on these LIES.

From SNL's very first episode... their first "fake commercial."

Movement tracing of two shots (one bad, one good).

This is a quick demonstration of the shot playback feature of the Mantix X10 Elite system. This was dry fire at home, aiming at a target on the wall in the living room.

The conventional wisdom is that "you can't miss with a laser." Yes, you can! It's all about fundamentals, folks!

Good guy takes Thug #1's gun and shoots Thug #2 (who is shooting at victim).

A brief tutorial on setting up the Dremel Workstation and precision drilling of P80 pin holes.

How to view the interaction of the trigger bar "shark fin" and the striker safety plunger. Join us on the best P80 forum on the internet at: https://www.patriotgunbuilders.com/forums/

How many rounds to you need to defend yourself? However many it takes to eliminate the threat to your life PLUS ONE.

Watch the rear end of the slide shift a bit when the trigger is pulled on my P80. Join us on the best P80 forum on the internet at: https://www.patriotgunbuilders.com/forums/

Short demo of the benefits of good lighting at your Freedom Bench. Join us on the best P80 forum on the internet at: https://www.patriotgunbuilders.com/forums/

A quick demo of my new Work Sharp Precision Adjust knife sharpener. With this sharpener, even a novice can achieve a mirror, hair-shaving edge.

I found a replacement for my very first gun (lost in a fire). The external parts of the gun are in VERY good condition. I discovered some pitting and erosion of the barrel bore, though. Still shootable!

My first MicroTech!

Will Smith corrects the prop master after being muzzled. The prop master thanks him and then muzzles himself! The only editing I did is described in the video.

I wanted to try a different way of cutting off the P80 frame tabs. Is it better? Maybe not. It definitely requires a steady hand. I was able to remove most of the tab material. I intentionally stayed a little bit away from the frame, leaving some tab material behind that had to be sanded off. Join us on the best P80 forum on the internet at: https://www.patriotgunbuilders.com/forums/

This is a follow-up to my previous P80 RSA channel video about whether following the prescribed molded outline for the tab removal is enough. In this video, I demonstrate the removal of that additional tab material to ensure a smoothly-operating recoil spring assembly, which is critical to the reliable function of your P80. Join us on the best P80 forum on the internet at: https://www.patriotgunbuilders.com/forums/

A demonstration of how and why an under-finished P80 channel can cause problems with your pistol. Join us on the best P80 forum on the internet at: https://www.patriotgunbuilders.com/forums/

Using a new tool (MicroMark's Micro-Sander) for finishing the tabs and channel on a P80. Join us on the best P80 forum on the internet at: https://www.patriotgunbuilders.com/forums/

Edit to add: The video gets cut off at 7:00. Not sure why! Stand by. I assembled my slide while I wait for some parts for the frame. I had a factory Glock 19 (Gen 2) that I could test the slide on. When I racked the slide back, about half the time, it would get stuck there. The slide was getting hung up on the barrel. Here's how I fixed it. Join us on the best P80 forum on the internet at: https://www.patriotgunbuilders.com/forums/