RAPTURE PROOF LATE SPRING 2024
HE WALKED AWAY AND LEFT THEM BEHIND.... JUST AS THE COMING RAPTURE WILL LEAVE MANY BEHIND. KEEP AWAKE KEEP ALERT HE IS AT THE DOOR SO BE DOING WHAT MAKES YOUR MASTER HAPPY UPON HIS RETURN ELSE YOU LOOSE YOUR CLOTHES AS THOSE WATCHMEN DID BY FALLING ASLEEP ON THE JOB.
90
views
6
comments
Mummified cat man head found in Peru
Nov12, 2023. This announcement came originally from Brien Forester, archeologist.
Such things a great in number, yet the deep state has for many years, hidden these from public view. They are not shown in a single textbook in schools. This would cause religious debate, because the bible claims giants existed, as well as aliens, reptilian humanoids and the like. They wish to keep your eyes closed and your minds empty.
123
views
1
comment
Finally, making capacitors for the zpe ion drive
Artifact design segment; the quad caps prep.
128
views
1
comment
Artifact V4
anti gravity was proven by Stan Deyo, suppressed by the CIA deep state. Even today he wont talk about his tech, let alone build or experiment in the public eye.
Zero point energy has been proven as well. All I needed was to find a way to combine these.
In lieu of a carrier wave, a bias of voltage through spark gap in this lens shaped array of coils, will form a continuous pump z wave among all the coils.
Deyo lift: estimated over 60lbs with 10 coil pairs @ 20kv dc pulsing.
Grebennikov lift: 200lbs (tested) using up to 2 square feet of area having paper thin bug wings as the only zpe device).
Artifact lift: estimated over 800lbs. Why? The static field produced from bug wings would never compare, as the real field is relative to energy of electrons ejected from the apex of the cone (in that case, the cones could only be seen under electron microscope). Together, his array projected a combined force that became tanjental in potential. There is no way to calculate that relative force with much accuracy, but with Deyo's array there is. Even if his array gave a mere 60lbs of lift with 30 coils at 20kv, this would produce at least 144lbs of lift at 20kv, and 288@40kv minimum. I have estimated, however, that if neutral ions are split here, through this ferrous bell shape, the compression waves made into it's apex even at 10kv should increase the potential of the surrounding flatwire capacitors, even the potential of capacitive resistance among all the coils and from those to the bell apex. This resulting charge increase gives negative ion bias to the top part of the bell, positive at the base, thereby polarizing this bell shape with superconductive level heavy ions about the same mass as gold, in a much thicker layer than was possible with Deyo's or Grebennikov's system.
Someday I hope to use the field it produces to grow graphene and other materials used to make superior capacitors for much more lift efficiency.
...
276
views
4
comments
Anti gravity construction
Using the principle of stan deyo's device that ripped itself almost out of the power supply with anti gravity force, Combine with 0 point energy to recycle the power, Combine with the geometric design of borobudur temple To force a specific manner of super conductive filtering by interlocking magnetic fields. The principle is very simple. Each of the 3 layers of coil pairs 32 24 16 acts as a dynamo, Runs in series with a 4 leaf clover shaped flatwire coil infinite loop. Supplying modulation to these externally And temporarily just to start the device Causes charge to build in the core of the clover At the same time this compressive force to the Apex Tries to push charge to another ground, Is that of the main winding having a tourist core in spiral core With yet another smaller thin wire spiral record in the middle of that to discharge As a capacitor , Providing an end result of repelling and attracting alternating alternating current force between 2 heavy grounds , The Carrier wave activated as as electrical discharge between contacts inside a glass tube. Spark gap spacing will determine the voltage of that that discharge, And therefore determine the overall output and timing . I suspect that even a low voltage will cause fantastic lifantastic lift so in this case I will need to have some other Medium in the circuit to prevent excess power excess lift. In the event there is not enough power I will need to add a second and 3rd layer to the spiral winding inside of the largest tube. This in other words means an extra 0 point where energy is made. A wire connects from that spiral winding to the finewire winding that goes around the glass tube. That wire is welded to a copper ball on the Apex much like a Tesla coil. The object there is to waste energy because the circuit is inductive. The more power inducted means the more ion charge is neutralized outside in the presence of shedding positive ions.
Artifact production
The extraordinary experiment of 0 point energy for anti gravity. Implosive 0 point energy is a proven science. The only real experiment here is discovering how much lift this thing will actually produce or in other words how over efficient it is.
Lotus plasma cutter review
I've been testing this for a while. The only problem it seems to have is not wanting to restart a cut once in a while so I have to cycle the power
2
comments
Table Rock Lake July 2021
Just going for pizza on the lake.
Forgot to video the glass house and the pizza dock wasn't anything special but the water was pretty smooth and the sunset was great.
52
views
New CR10s Thermostor problem
Why the thermostat fails on CR10 or any 3-D printer, usually.
44
views
1
comment
New Cr10s bad thermistor
I use the very accurate temperature sensing optical probe to determine What I think I already knew. My polycarbonate prints were coming out very very stringy and I could not get material to stick together.
77
views
CR10S 3d print success
Using the updated firmware that was very difficult , Although I discovered this model allows you to update the firmware just by plugging into your computer without the adurino device!
All of these parts go through round tubes so there is no there is no way to make accurate parts simply by cutting out sections of polycarbonate sheet.
50
views
Crealty cr10 3d printing experience
A first time user experience for this machine
34
views
1
comment