The Way To Native Chronicles

This video takes a close look at an unusual Ruger No. 1 - chambered for the .45-120 cartridge - and shares some of the history behind its making and the method of reloading ammunition for it. The .45-120 was a cartridge developed near the end of the buffalo hunting era (the one in the "Quigley Down Under" movie was a .45-110 - classified as "experimental" at that time). In addition to the custom chambering, this rifle also has a hand-made stock and custom engraving with gold inlay. In spite of those visual enhancements, I use this rifle the most for hunting moose, deer and bear (it works very well). The smokeless load I developed gets the 535 grain cast bullet going to about 1,600 fps; facilitating a fairly flat trajectory (which is what I want when hunting). Due to the incredible strength of the Ruger No. 1 falling block action and the large case capacity (originally designed for black powder), I could easily make this load more powerful than a modern .458 Winchester Magnum, but that would be more punishing than is necessary for my purposes. The rifle weighing about 11 lbs, with a muzzle velocity of 1,600 fps applied to the 535 grain, the recoil comes in at about 33 ft-lbs, which is not too bad. DISCLAIMER: My videos are strictly for documentary, educational, and entertainment purposes only. Imitation or the use of any acts depicted in my videos is solely AT YOUR OWN RISK. All work on firearms should be carried out by a licensed individual and all state, provincial and federal rules apply to such. I (including YouTube) will not be held liable for any injury to yourself or damage to your firearms resulting from attempting anything shown in any of my videos. I do not endorse any specific product and this video is not an attempt to sell you a good or service. I am not a gun store and DO NOT sell or deal in firearms. Such a practice is heavily regulated and subject to applicable laws. I DO NOT sell parts, magazines, or firearms. These videos are free to watch and if anyone attempts to charge for this video notify me immediately. By viewing or flagging this video you are acknowledging the above. Fair Use: In the rare instance I include someone else’s footage, that is covered in Fair Use for Documentary and Educational purposes with the intention of driving commentary and allowing freedom of speech.

This video provides a close-up look at my custom Ruger No. 1 rifle chambered for the .45-120. This is a cartridge that was developed near the end of the buffalo hunting era (the one in the "Quigley Down Under" movie was a .45-110 - classified as "experimental" at that time). In addition to the custom chambering, this rifle also has a hand-made stock and custom engraving with gold inlay. In spite of those visual enhancements, I use this rifle the most for hunting moose, deer and bear (it works very well). The smokeless load I developed gets the 535 grain cast bullet going to about 1,600 fps; facilitating a fairly flat trajectory (which is what I want when hunting). Due to the incredible strength of the Ruger No. 1 falling block action and the large case capacity (originally designed for black powder), I could easily make this load more powerful than a modern .458 Winchester Magnum, but that would be more punishing than is necessary for my purposes. The rifle weighing about 11 lbs, with a muzzle velocity of 1,600 fps applied to the 535 grain, the recoil comes in at about 33 ft-lbs, which is not too bad. DISCLAIMER: My videos are strictly for documentary, educational, and entertainment purposes only. Imitation or the use of any acts depicted in my videos is solely AT YOUR OWN RISK. All work on firearms should be carried out by a licensed individual and all state, provincial and federal rules apply to such. I (including YouTube) will not be held liable for any injury to yourself or damage to your firearms resulting from attempting anything shown in any of my videos. I do not endorse any specific product and this video is not an attempt to sell you a good or service. I am not a gun store and DO NOT sell or deal in firearms. Such a practice is heavily regulated and subject to applicable laws. I DO NOT sell parts, magazines, or firearms. These videos are free to watch and if anyone attempts to charge for this video notify me immediately. By viewing or flagging this video you are acknowledging the above. Fair Use: In the rare instance I include someone else’s footage, that is covered in Fair Use for Documentary and Educational purposes with the intention of driving commentary and allowing freedom of speech.

In this video I share the process of taking wheel weights, melting them down, cleaning the alloy and then converting it into ingots - ready to use for making cast bullets later. DISCLAIMER: My videos are strictly for documentary, educational, and entertainment purposes only. Imitation or the use of any acts depicted in my videos is solely AT YOUR OWN RISK. All work on firearms should be carried out by a licensed individual and all state, provincial and federal rules apply to such. I (including YouTube) will not be held liable for any injury to yourself or damage to your firearms resulting from attempting anything shown in any of my videos. I do not endorse any specific product and this video is not an attempt to sell you a good or service. I am not a gun store and DO NOT sell or deal in firearms. Such a practice is heavily regulated and subject to applicable laws. I DO NOT sell parts, magazines, or firearms. These videos are free to watch and if anyone attempts to charge for this video notify me immediately. By viewing or flagging this video you are acknowledging the above. Fair Use: In the rare instance I include someone else’s footage, that is covered in Fair Use for Documentary and Educational purposes with the intention of driving commentary and allowing freedom of speech.

The compact Mares Leg rifles receive a bit of attention as possible solutions for protection in the bush, but there's doubts about whether you can hit anything with them, so here's a simple demonstration to give an idea. This one is chambered for .44 Mag using 245 grain cast bullets ahead of 24.0 grains of 4227 with muzzle velocity of 1,640 fps, so plenty of punch for a little rig. DISCLAIMER: My videos are strictly for documentary, educational, and entertainment purposes only. Imitation or the use of any acts depicted in my videos is solely AT YOUR OWN RISK. All work on firearms should be carried out by a licensed individual and all state, provincial and federal rules apply to such. I (including YouTube) will not be held liable for any injury to yourself or damage to your firearms resulting from attempting anything shown in any of my videos. I do not endorse any specific product and this video is not an attempt to sell you a good or service. I am not a gun store and DO NOT sell or deal in firearms. Such a practice is heavily regulated and subject to applicable laws. I DO NOT sell parts, magazines, or firearms. These videos are free to watch and if anyone attempts to charge for this video notify me immediately. By viewing or flagging this video you are acknowledging the above. Fair Use: In the rare instance I include someone else’s footage, that is covered in Fair Use for Documentary and Educational purposes with the intention of driving commentary and allowing freedom of speech.

This video examines a frustrating jamming problem rifles with top-loading magazines are prone to and how to avoid it. The rifle used in this example is a Winchester Model 670 chambered for .243. Caveat: Rifles that have claw extractors (like the pre-64 Winchester Model 70's and 98 Mausers) must feed the cartridges from their magazines. With those guns you cannot manually load a round in the chamber and then close the bolt over top. Instead, you have to feed the round in from the magazine. DISCLAIMER: My videos are strictly for documentary, educational, and entertainment purposes only. Imitation or the use of any acts depicted in my videos is solely AT YOUR OWN RISK. All work on firearms should be carried out by a licensed individual and all state, provincial and federal rules apply to such. I (including YouTube) will not be held liable for any injury to yourself or damage to your firearms resulting from attempting anything shown in any of my videos. I do not endorse any specific product and this video is not an attempt to sell you a good or service. I am not a gun store and DO NOT sell or deal in firearms. Such a practice is heavily regulated and subject to applicable laws. I DO NOT sell parts, magazines, or firearms. These videos are free to watch and if anyone attempts to charge for this video notify me immediately. By viewing or flagging this video you are acknowledging the above. Fair Use: In the rare instance I include someone else’s footage, that is covered in Fair Use for Documentary and Educational purposes with the intention of driving commentary and allowing freedom of speech.

Since I wanted to make a couple of sets of these, figured I'd pass along what I learned while doing it, in case it's of use to someone else. Costs practically nothing to make, so no harm in making more than one set in different lengths. DISCLAIMER: My videos are strictly for documentary, educational, and entertainment purposes only. Imitation or the use of any acts depicted in my videos is solely AT YOUR OWN RISK. All work on firearms should be carried out by a licensed individual and all state, provincial and federal rules apply to such. I (including YouTube) will not be held liable for any injury to yourself or damage to your firearms resulting from attempting anything shown in any of my videos. I do not endorse any specific product and this video is not an attempt to sell you a good or service. I am not a gun store and DO NOT sell or deal in firearms. Such a practice is heavily regulated and subject to applicable laws. I DO NOT sell parts, magazines, or firearms. These videos are free to watch and if anyone attempts to charge for this video notify me immediately. By viewing or flagging this video you are acknowledging the above. Fair Use: In the rare instance I include someone else’s footage, that is covered in Fair Use for Documentary and Educational purposes with the intention of driving commentary and allowing freedom of speech.

In this video, an attempt is made to determine how much improvement one can expect from using some form of case filler. Keeping all other variables the same, 12 cartridges are loaded using filler and another 12 loaded without. The two sets are then tested in the field using a chronograph. A number of circumstances can require filling cases with powder taking up far less volume than the case has available. A concern arises from this however: Unless filler is used, partial filling may lead to erratic combustion since the powder is free to settle in different positions inside the case when the primer ignites. A long-used solution is adding some sort of filler to take up the extra space, so the powder is kept in position against the primer. In this video I examine some pros and cons of this method. The rifle used is a Ruger No. 1, custom-chambered for the buffalo-hunting-era .45-120 cartridge, firing 535 grain cast bullets. Having a large case capacity (due to originally being intended for black powder), if you decide to use smokeless instead, you are going to end up with a lot of unused space, since so much less of smokeless is required. There are conflicting reports about the advisability of using fillers. Some warn that it can result in ringed chambers due to over-pressure if the filler wads up inside. Although not covering every aspect of filler use, this video does look at some of the risks/benefits involved and whether the same concerns apply for all cartridge types and shooting needs. After the range test, an analysis of the test data is conducted. This portion of the video may also be helpful to some, since techniques for conducting such analysis using statistical methods are shared. DISCLAIMER: My videos are strictly for documentary, educational, and entertainment purposes only. Imitation or the use of any acts depicted in my videos is solely AT YOUR OWN RISK. All work on firearms should be carried out by a licensed individual and all state, provincial and federal rules apply to such. I (including YouTube) will not be held liable for any injury to yourself or damage to your firearms resulting from attempting anything shown in any of my videos. I do not endorse any specific product and this video is not an attempt to sell you a good or service. I am not a gun store and DO NOT sell or deal in firearms. Such a practice is heavily regulated and subject to applicable laws. I DO NOT sell parts, magazines, or firearms. These videos are free to watch and if anyone attempts to charge for this video notify me immediately. By viewing or flagging this video you are acknowledging the above. Fair Use: In the rare instance I include someone else’s footage, that is covered in Fair Use for Documentary and Educational purposes with the intention of driving commentary and allowing freedom of speech.

A firearm with a tube magazine can fool you into thinking it has been unloaded when it's not. This is an important safety issue owners of such guns should be made aware of. Yet I don't recall ever seeing it addressed by anyone, so I'll do it. The rifle used in the video is a Rossi Ranch Hand, chambered for .44 Magnum. DISCLAIMER: My videos are strictly for documentary, educational, and entertainment purposes only. Imitation or the use of any acts depicted in my videos is solely AT YOUR OWN RISK. All work on firearms should be carried out by a licensed individual and all state, provincial and federal rules apply to such. I (including YouTube) will not be held liable for any injury to yourself or damage to your firearms resulting from attempting anything shown in any of my videos. I do not endorse any specific product and this video is not an attempt to sell you a good or service. I am not a gun store and DO NOT sell or deal in firearms. Such a practice is heavily regulated and subject to applicable laws. I DO NOT sell parts, magazines, or firearms. These videos are free to watch and if anyone attempts to charge for this video notify me immediately. By viewing or flagging this video you are acknowledging the above. Fair Use: In the rare instance I include someone else’s footage, that is covered in Fair Use for Documentary and Educational purposes with the intention of driving commentary and allowing freedom of speech.

Knowing how to cut up a moose doesn't just save on butchering costs; it also enables you - if the animal has to be hauled from deep bush - to carve it up on the spot first, so you can carry out lighter portions, instead of entire quarters at a time. This is a common skill among First Nations since they often process their game right in camp. This video features two "Dene Tha" women to show you how it's done. The video is quite long but, if you want to learn, this a good way to get yourself prepared. The butchering shown is processing the hind quarters, where most of the best meat resides. DISCLAIMER: My videos are strictly for documentary, educational, and entertainment purposes only. Imitation or the use of any acts depicted in my videos is solely AT YOUR OWN RISK. All work on firearms should be carried out by a licensed individual and all state, provincial and federal rules apply to such. I (including YouTube) will not be held liable for any injury to yourself or damage to your firearms resulting from attempting anything shown in any of my videos. I do not endorse any specific product and this video is not an attempt to sell you a good or service. I am not a gun store and DO NOT sell or deal in firearms. Such a practice is heavily regulated and subject to applicable laws. I DO NOT sell parts, magazines, or firearms. These videos are free to watch and if anyone attempts to charge for this video notify me immediately. By viewing or flagging this video you are acknowledging the above. Fair Use: In the rare instance I include someone else’s footage, that is covered in Fair Use for Documentary and Educational purposes with the intention of driving commentary and allowing freedom of speech.

Just a short, fun video, showing my grandchildren helping out. It's a good thing to get kids involved with simple reloading tasks. They seem to take a keen interest in machines and mechanically crunching stuff. Just be sure to keep them supervised as they do! DISCLAIMER: My videos are strictly for documentary, educational, and entertainment purposes only. Imitation or the use of any acts depicted in my videos is solely AT YOUR OWN RISK. All work on firearms should be carried out by a licensed individual and all state, provincial and federal rules apply to such. I (including YouTube) will not be held liable for any injury to yourself or damage to your firearms resulting from attempting anything shown in any of my videos. I do not endorse any specific product and this video is not an attempt to sell you a good or service. I am not a gun store and DO NOT sell or deal in firearms. Such a practice is heavily regulated and subject to applicable laws. I DO NOT sell parts, magazines, or firearms. These videos are free to watch and if anyone attempts to charge for this video notify me immediately. By viewing or flagging this video you are acknowledging the above. Fair Use: In the rare instance I include someone else’s footage, that is covered in Fair Use for Documentary and Educational purposes with the intention of driving commentary and allowing freedom of speech.

This brief video shows bullets being extracted from a normal oven and doused in cold water, for the purpose of increasing their hardness (a process known as "heat treating"). DISCLAIMER: My videos are strictly for documentary, educational, and entertainment purposes only. Imitation or the use of any acts depicted in my videos is solely AT YOUR OWN RISK. All work on firearms should be carried out by a licensed individual and all state, provincial and federal rules apply to such. I (including YouTube) will not be held liable for any injury to yourself or damage to your firearms resulting from attempting anything shown in any of my videos. I do not endorse any specific product and this video is not an attempt to sell you a good or service. I am not a gun store and DO NOT sell or deal in firearms. Such a practice is heavily regulated and subject to applicable laws. I DO NOT sell parts, magazines, or firearms. These videos are free to watch and if anyone attempts to charge for this video notify me immediately. By viewing or flagging this video you are acknowledging the above. Fair Use: In the rare instance I include someone else’s footage, that is covered in Fair Use for Documentary and Educational purposes with the intention of driving commentary and allowing freedom of speech.

Yes, you can apply gas checks to plain-based bullets! This video shows you how (and what kind of gas checks to use). DISCLAIMER: My videos are strictly for documentary, educational, and entertainment purposes only. Imitation or the use of any acts depicted in my videos is solely AT YOUR OWN RISK. All work on firearms should be carried out by a licensed individual and all state, provincial and federal rules apply to such. I (including YouTube) will not be held liable for any injury to yourself or damage to your firearms resulting from attempting anything shown in any of my videos. I do not endorse any specific product and this video is not an attempt to sell you a good or service. I am not a gun store and DO NOT sell or deal in firearms. Such a practice is heavily regulated and subject to applicable laws. I DO NOT sell parts, magazines, or firearms. These videos are free to watch and if anyone attempts to charge for this video notify me immediately. By viewing or flagging this video you are acknowledging the above. Fair Use: In the rare instance I include someone else’s footage, that is covered in Fair Use for Documentary and Educational purposes with the intention of driving commentary and allowing freedom of speech.

This video suggests leaving a thick sprue on top of the mould to make the casting process a bit smoother. Also shown is a simple foot-operated mechanism for controlling the pour and the 'tandem' method of using two moulds at once when casting, which leaves more time for sprues to cool without slowing down the casting rhythm. DISCLAIMER: My videos are strictly for documentary, educational, and entertainment purposes only. Imitation or the use of any acts depicted in my videos is solely AT YOUR OWN RISK. All work on firearms should be carried out by a licensed individual and all state, provincial and federal rules apply to such. I (including YouTube) will not be held liable for any injury to yourself or damage to your firearms resulting from attempting anything shown in any of my videos. I do not endorse any specific product and this video is not an attempt to sell you a good or service. I am not a gun store and DO NOT sell or deal in firearms. Such a practice is heavily regulated and subject to applicable laws. I DO NOT sell parts, magazines, or firearms. These videos are free to watch and if anyone attempts to charge for this video notify me immediately. By viewing or flagging this video you are acknowledging the above. Fair Use: In the rare instance I include someone else’s footage, that is covered in Fair Use for Documentary and Educational purposes with the intention of driving commentary and allowing freedom of speech.

If you have a pair of vice grips, you don't need to buy an expensive bullet-pulling tool (especially if you don't mind ruining the bullet, once removed). The hammer-style tools tend to break and are slow anyway. This video demonstrates pulling bullets quickly and simply, using just a pair of vice grips. DISCLAIMER: My videos are strictly for documentary, educational, and entertainment purposes only. Imitation or the use of any acts depicted in my videos is solely AT YOUR OWN RISK. All work on firearms should be carried out by a licensed individual and all state, provincial and federal rules apply to such. I (including YouTube) will not be held liable for any injury to yourself or damage to your firearms resulting from attempting anything shown in any of my videos. I do not endorse any specific product and this video is not an attempt to sell you a good or service. I am not a gun store and DO NOT sell or deal in firearms. Such a practice is heavily regulated and subject to applicable laws. I DO NOT sell parts, magazines, or firearms. These videos are free to watch and if anyone attempts to charge for this video notify me immediately. By viewing or flagging this video you are acknowledging the above. Fair Use: In the rare instance I include someone else’s footage, that is covered in Fair Use for Documentary and Educational purposes with the intention of driving commentary and allowing freedom of speech.

There's a great sense of satisfaction, resurrecting the old .45-120 cartridge (used for hunting buffalo in 1890's) for modern use in hunting - bringing down moose-size game well within its capabilities. What this video shows is how I manage, using smokeless powder and my own cast bullets. Every step in the reloading process is depicted - even the melting down of wheel weight metal and casting the bullets. DISCLAIMER: My videos are strictly for documentary, educational, and entertainment purposes only. Imitation or the use of any acts depicted in my videos is solely AT YOUR OWN RISK. All work on firearms should be carried out by a licensed individual and all state, provincial and federal rules apply to such. I (including YouTube) will not be held liable for any injury to yourself or damage to your firearms resulting from attempting anything shown in any of my videos. I do not endorse any specific product and this video is not an attempt to sell you a good or service. I am not a gun store and DO NOT sell or deal in firearms. Such a practice is heavily regulated and subject to applicable laws. I DO NOT sell parts, magazines, or firearms. These videos are free to watch and if anyone attempts to charge for this video notify me immediately. By viewing or flagging this video you are acknowledging the above. Fair Use: In the rare instance I include someone else’s footage, that is covered in Fair Use for Documentary and Educational purposes with the intention of driving commentary and allowing freedom of speech.

This video discusses the issue of fitting reloaded cartridges so that the front driving band of the bullet engages the rifling of the barrel. This is made more difficult in the case of falling block rifles, since a rising and falling block does not provide any camming force against the base of the bullet to seat it. DISCLAIMER: My videos are strictly for documentary, educational, and entertainment purposes only. Imitation or the use of any acts depicted in my videos is solely AT YOUR OWN RISK. All work on firearms should be carried out by a licensed individual and all state, provincial and federal rules apply to such. I (including YouTube) will not be held liable for any injury to yourself or damage to your firearms resulting from attempting anything shown in any of my videos. I do not endorse any specific product and this video is not an attempt to sell you a good or service. I am not a gun store and DO NOT sell or deal in firearms. Such a practice is heavily regulated and subject to applicable laws. I DO NOT sell parts, magazines, or firearms. These videos are free to watch and if anyone attempts to charge for this video notify me immediately. By viewing or flagging this video you are acknowledging the above. Fair Use: In the rare instance I include someone else’s footage, that is covered in Fair Use for Documentary and Educational purposes with the intention of driving commentary and allowing freedom of speech.

There are many opinions on the best way to lubricate cases and seat primers. This is the way I do it. DISCLAIMER: My videos are strictly for documentary, educational, and entertainment purposes only. Imitation or the use of any acts depicted in my videos is solely AT YOUR OWN RISK. All work on firearms should be carried out by a licensed individual and all state, provincial and federal rules apply to such. I (including YouTube) will not be held liable for any injury to yourself or damage to your firearms resulting from attempting anything shown in any of my videos. I do not endorse any specific product and this video is not an attempt to sell you a good or service. I am not a gun store and DO NOT sell or deal in firearms. Such a practice is heavily regulated and subject to applicable laws. I DO NOT sell parts, magazines, or firearms. These videos are free to watch and if anyone attempts to charge for this video notify me immediately. By viewing or flagging this video you are acknowledging the above. Fair Use: In the rare instance I include someone else’s footage, that is covered in Fair Use for Documentary and Educational purposes with the intention of driving commentary and allowing freedom of speech.

Besides flaring/belling the mouths of cases, to prepare them to accept cast bullets, there is another way. It only has to be done once for the life of the case and will likely result in the case lasting longer (from being worked less each time it's reloaded). This video shows you my technique of inside-reaming the case's mouth, just a little way in. DISCLAIMER: My videos are strictly for documentary, educational, and entertainment purposes only. Imitation or the use of any acts depicted in my videos is solely AT YOUR OWN RISK. All work on firearms should be carried out by a licensed individual and all state, provincial and federal rules apply to such. I (including YouTube) will not be held liable for any injury to yourself or damage to your firearms resulting from attempting anything shown in any of my videos. I do not endorse any specific product and this video is not an attempt to sell you a good or service. I am not a gun store and DO NOT sell or deal in firearms. Such a practice is heavily regulated and subject to applicable laws. I DO NOT sell parts, magazines, or firearms. These videos are free to watch and if anyone attempts to charge for this video notify me immediately. By viewing or flagging this video you are acknowledging the above. Fair Use: In the rare instance I include someone else’s footage, that is covered in Fair Use for Documentary and Educational purposes with the intention of driving commentary and allowing freedom of speech.

This video provides a comprehensive view of every aspect in the cartridge reloading process - right from the melting down wheel weights (to make alloy ingots), to casting, resizing cases and seating the bullets. DISCLAIMER: My videos are strictly for documentary, educational, and entertainment purposes only. Imitation or the use of any acts depicted in my videos is solely AT YOUR OWN RISK. All work on firearms should be carried out by a licensed individual and all state, provincial and federal rules apply to such. I (including YouTube) will not be held liable for any injury to yourself or damage to your firearms resulting from attempting anything shown in any of my videos. I do not endorse any specific product and this video is not an attempt to sell you a good or service. I am not a gun store and DO NOT sell or deal in firearms. Such a practice is heavily regulated and subject to applicable laws. I DO NOT sell parts, magazines, or firearms. These videos are free to watch and if anyone attempts to charge for this video notify me immediately. By viewing or flagging this video you are acknowledging the above. Fair Use: In the rare instance I include someone else’s footage, that is covered in Fair Use for Documentary and Educational purposes with the intention of driving commentary and allowing freedom of speech.

Using a set of dies made by "Patmarlins", this video shows how use them to make gas checks on your own.

This video shows how I sort-out bullets that don't make the grade after a bullet casting session. DISCLAIMER: My videos are strictly for documentary, educational, and entertainment purposes only. Imitation or the use of any acts depicted in my videos is solely AT YOUR OWN RISK. All work on firearms should be carried out by a licensed individual and all state, provincial and federal rules apply to such. I (including YouTube) will not be held liable for any injury to yourself or damage to your firearms resulting from attempting anything shown in any of my videos. I do not endorse any specific product and this video is not an attempt to sell you a good or service. I am not a gun store and DO NOT sell or deal in firearms. Such a practice is heavily regulated and subject to applicable laws. I DO NOT sell parts, magazines, or firearms. These videos are free to watch and if anyone attempts to charge for this video notify me immediately. By viewing or flagging this video you are acknowledging the above. Fair Use: In the rare instance I include someone else’s footage, that is covered in Fair Use for Documentary and Educational purposes with the intention of driving commentary and allowing freedom of speech.

When changing the H&I dies in a lubrisizer, it is crucial that you do it the right way and not cross-thread while doing so (to prevent ruining the threads in the body of the lubrisizer), so this video shows how to do that the right way. In addition, new users of lubrisizers are sometimes stumped when it comes to changing the lube stick in the device once it has run empty, so this video demonstrates that procedure as well. DISCLAIMER: My videos are strictly for documentary, educational, and entertainment purposes only. Imitation or the use of any acts depicted in my videos is solely AT YOUR OWN RISK. All work on firearms should be carried out by a licensed individual and all state, provincial and federal rules apply to such. I (including YouTube) will not be held liable for any injury to yourself or damage to your firearms resulting from attempting anything shown in any of my videos. I do not endorse any specific product and this video is not an attempt to sell you a good or service. I am not a gun store and DO NOT sell or deal in firearms. Such a practice is heavily regulated and subject to applicable laws. I DO NOT sell parts, magazines, or firearms. These videos are free to watch and if anyone attempts to charge for this video notify me immediately. By viewing or flagging this video you are acknowledging the above. Fair Use: In the rare instance I include someone else’s footage, that is covered in Fair Use for Documentary and Educational purposes with the intention of driving commentary and allowing freedom of speech.

This video shows my method and setup for casting bullets, from the start of the process to the very end. DISCLAIMER: My videos are strictly for documentary, educational, and entertainment purposes only. Imitation or the use of any acts depicted in my videos is solely AT YOUR OWN RISK. All work on firearms should be carried out by a licensed individual and all state, provincial and federal rules apply to such. I (including YouTube) will not be held liable for any injury to yourself or damage to your firearms resulting from attempting anything shown in any of my videos. I do not endorse any specific product and this video is not an attempt to sell you a good or service. I am not a gun store and DO NOT sell or deal in firearms. Such a practice is heavily regulated and subject to applicable laws. I DO NOT sell parts, magazines, or firearms. These videos are free to watch and if anyone attempts to charge for this video notify me immediately. By viewing or flagging this video you are acknowledging the above. Fair Use: In the rare instance I include someone else’s footage, that is covered in Fair Use for Documentary and Educational purposes with the intention of driving commentary and allowing freedom of speech.

Sighting in a rifle for hunting in the field is a very different proposition than sighting in for accuracy on a range at known distances. Applying the concept of "Point Blank Range", this video (with on-screen examples) will show you how to choose the best distance to zero-in your rifle for whatever cartridge you shoot. Far too many hunters - basing their decisions on outdated custom - short-change themselves by zeroing-in at distances that are far too close. DISCLAIMER: My videos are strictly for documentary, educational, and entertainment purposes only. Imitation or the use of any acts depicted in my videos is solely AT YOUR OWN RISK. All work on firearms should be carried out by a licensed individual and all state, provincial and federal rules apply to such. I (including YouTube) will not be held liable for any injury to yourself or damage to your firearms resulting from attempting anything shown in any of my videos. I do not endorse any specific product and this video is not an attempt to sell you a good or service. I am not a gun store and DO NOT sell or deal in firearms. Such a practice is heavily regulated and subject to applicable laws. I DO NOT sell parts, magazines, or firearms. These videos are free to watch and if anyone attempts to charge for this video notify me immediately. By viewing or flagging this video you are acknowledging the above. Fair Use: In the rare instance I include someone else’s footage, that is covered in Fair Use for Documentary and Educational purposes with the intention of driving commentary and allowing freedom of speech.

A compilation of 3 videos, showing the test results of 3 rifles, to determine their penetration capabilities. Looks like the single-shot "buffalo rifle" distinguishes itself! DISCLAIMER: My videos are strictly for documentary, educational, and entertainment purposes only. Imitation or the use of any acts depicted in my videos is solely AT YOUR OWN RISK. All work on firearms should be carried out by a licensed individual and all state, provincial and federal rules apply to such. I (including YouTube) will not be held liable for any injury to yourself or damage to your firearms resulting from attempting anything shown in any of my videos. I do not endorse any specific product and this video is not an attempt to sell you a good or service. I am not a gun store and DO NOT sell or deal in firearms. Such a practice is heavily regulated and subject to applicable laws. I DO NOT sell parts, magazines, or firearms. These videos are free to watch and if anyone attempts to charge for this video notify me immediately. By viewing or flagging this video you are acknowledging the above. Fair Use: In the rare instance I include someone else’s footage, that is covered in Fair Use for Documentary and Educational purposes with the intention of driving commentary and allowing freedom of speech.