TriggerShims

How to Install a 10/22 Volquartsen Exact Edge Extractor In this Video, We Install a Replacement Rimfire Shell Extractor in a Ruger 10/22 Rifle @ https://www.triggershims.com/ Manufactured through an EDM Process to Produce Exacting Tolerances Made of A2 Tool Steel Hardened to Rc 58-60 The Hook is .005" Closer to the Rim of the Cartridge to Allow for the Most Positive Extraction Available! Will Not Lose It's Edge Under Impact Solves Jamming and Stove Pipe Issues Another Must-Have for 10/22, 22/45 and MkI MkII MkIII Owners! Also Fits ~ Thompson/Center T/CR22

Installation Instructions for the Ruger 10/22 1022 Automatic Bolt Release and the Extended Magazine Release by Volquartsen available at TriggerShims.com at http://www.triggershims.com/

I install a Wolff 13 Pound Recoil Spring Set in a Ruger LCP .380 The Wolff Extra Power Recoil Spring set can reduce your felt recoil, allows fasted follow-up, and improves function with Heavy Loads. Also reduces the wear on your gun over the 9 pound factory spring. Available at http://triggershims.com/ I also have the same kits for the Kel-Tec P-3AT

In this video, we install a JP Enterprises Trigger and Hammer Spring Kit. This Spring Kit includes the Hammer Spring, Trigger Spring and Disconnector Spring. Easy to Install, this kit will Lower the Trigger Pull to between 4.5 and 5 pounds, can be done in less than a half hour, and no Permanent Modifications are made. This kit is available at http://www.TriggerShims.com/ For Recreational or Competition use only. This kit should not be used in Military or Law Enforcement Applications

Hi Folks, Lance here from http://www.TriggerShims.com In this video, I check the Trigger Pull on a Brand New Out-of-Box 10/22 Charger using a RCBS Trigger Pull Gauge. The average Trigger Pull on this gun was quite good for stock, 4 pounds 4 ounces I also have a Complete Tear-Down and Reassembly Video of this Trigger Assembly; Ruger 1022 Trigger Tear Down Video Part I at; http://youtu.be/Jsry8fvIRc0 and Ruger 1022 Trigger Reassembly Video Part II at; http://youtu.be/OIsQALxLk24

How To Install a Wolff 34910 AR-15 Trigger Spring Kit. This Kit is Available at http://www.triggershims.com/ The Wolff Reduced Power Trigger Function Pak contains 1 Reduced Power Trigger Spring and Reduced Power Disconnector Spring. Designed to lighten and improved trigger function. We remove the Hammer, Trigger and Disconnector to install this kit.

How To Fit and Install a http://www.TriggerShims.com Brand Shim Kit in a New Model Ruger Single Action. This Video Applies to the Single Six, Blackhawk, Bisley and Vaquero. The Gun Featured in this Video is a New Model Flat-Top Blackhawk in .44 Special This kit is available at http://www.TriggerShims.com/

Available at https://www.triggershims.com/ Our TriggerShims Brand AR-15 Compensator Shims can be used to Align your Muzzle Device, Muzzle Brake, Compensator or Flash Suppressor on your 1/2" Threaded Barrel. These Tempered Stainless Steel USA Made Shims Ensure Correct Fit and Precise Alignment of your Muzzle Device. Our AR-15 Compensator Shim Pak offers a Greater Degree of Precision than any Crush or Peel Washer while also being Faster and Less Labor Intensive to Install. Multiple Shims may be Stacked and Used Together as Necessary in Order to Achieve the Exact Thickness Required for Proper Orientation. These Shims will fit any 1/2" Threaded Barrel including Rifles and Hand Guns that have a 3/4" O.D. Muzzle Device. These Shims are 3/4" OD X .510" ID and are Available at http://www.TriggerShims.com/ We also have AR-10 shims available AR-10 Shims are 5/8" X 3/4" Nominal size

Remove and Re-Install Ruger DA Mainspring from a Ruger Super Redhawk. This method can also be used on the Ruger SP101, GP100, Redhawk, Blackhawk, Most Single Action Revolvers with Coil Mainsprings, and Ruger 10/22 among others. Wolff Spring Kits Available at http://www.TriggerShims.com/

Hi Folks, Lance here from http://www.TriggerShims.com In this How To Video I Assemble a Dedicated .22 Caliber Upper Receiver for my AR-15 using a CMMG .22 Caliber Bravo Model SS Conversion Kit with 25 Round Magazine, a CMMG WASP M4 Contour .22 LR Barrel with 1:16 Twist, a UTG Pro Full Float Hand Guard and UTG Pro Quad Rail Gas Block, and a DPMS A1 Flash Hider. I mount this Upper Receiver on my old stand-by Olympic Arms "Live Free or Die" Lower Receiver which has a UTG Pro 6 Position Mil-Spec M4/AR15 Collapsible Stock. I have had this gun for a year now, and I wanted to do this video to show how easy it was to assemble a Dedicated .22 Cal AR-15 Upper. The CMMG Conversion has worked flawlessly for me and the CMMG WASP Barrel is quite accurate. The whole thing is topped off with a Rimfire Optimized Nikon P-22 2-7X32 with BDC 150 Reticle that not only looks good with the matching AR Platform Rings, but is clear and easy to use. I have had so much fun with this gun that it has achieved Favorite Gun Status in my book. If you talk to the folks at CMMG or Nikon, tell them Lance sent you, and I Promise that their products would not disappoint. For all your Gun Shim Needs, stop by and see me at TriggerShims.com

Hi Folks, Lance here from http://www.TriggerShims.com​ In this video, we install a new Volquartsen A2 SureStrike Firing Pin in our 10/22 Rifle. The Replacement Firing Pin in a nice upgrade, and is available at http://www.triggershims.com/​ We also have a companion video that shows how to install the replacement A2 Extractor and Spring.

In this How-To Video we install Hammer Shims and Lever Shims in a Henry Lever Action Varmint Express .17 HMR Rifle Trigger Shims, Hammer Shims and Lever Shims for the Henry and Other Rifles are available at http://www.TriggerShims.com/

How To Install a http://www.TriggerShims.com​ Brand Shim Kit in your Ruger 10/22 Shows how to install the TriggerShims #10/22-8SS 8 Piece Shim Kit Our Ruger 10/22 Trigger Shim Kits will remove side play found in stock and custom trigger assemblies, will stop the trigger from rubbing the trigger housing and smooth the trigger pull, correctly centering the Hammer, Disconnector, Sear and Trigger, possibly improving accuracy. Also shows how to Remove and Reassemble the Hammer, Trigger, Sear, Disconnector, Bolt Release and Magazine Release. Shows how to install the Wolff Gunsprings 18076 10/22 Reduced Power Rifle Tune-Up Pak Shows how to Install the Volquartsen VC10BR Automatic Bolt Release and the Volquartsen VC10MR Extended Magazine Release Video is presented by Lance C. Shively - Owner of TriggerShims.com and Manufacturer of TriggerShims Brand Trigger Shim Kits This kit is available at http://www.TriggerShims.com/

I install a Wolff Non-Captive Guide Rod and Recoil Spring set in a Glock 17. I also install a New Striker Spring, and Show Removal of the Extractor. This Guide Rod Kit and other Wolff Springs are available at http://TriggerShims.com/​ We manufacture an extensive line of Gun Shims for Pistols, Revolvers, Rifles and AR Shims and sell a full line of Popular Wolff Gun Spring Paks.

This Video from http://www.TriggerShims.com​ shows the Basic Installation of the Bolt Shims used on a Ruger 77/22 or 77/17 Rifles Including .17 WSM, .17 HMR, .22 Long Rifle, .22 Magnum, .22 Hornet, .357 Magnum, & .44 Magnum These Bolt Shims will also work on the 2 piece bolts used in the 77/357 and 77/44 Rifles. Installing Bolt Shims can increase accuracy and can cure FTF from Light Strikes. These Shims are Available at http://www.triggershims.com/

This Video from http://www.TriggerShims.com shows the Installation of a Wolff Blitzschnell Striker Spring used on a Ruger 77/22 or 77/17 Hornet Shows How Striker is Disassembled using the Menck Bolt Tool Part # R&RBT The Striker Spring is part of a Wolff 30375 Spring Kit for the 77/22 and 77/17 This Spring Kit and the Bolt Tool are Available at http://www.triggershims.com/

In this video, I disassemble and reassemble a Ruger 77/357 Bolt, showing how to install Bolt Shims from http://TriggerShims.com/ At 3:40 I also show how to Unlock a Bolt if the Bolt Sleeve is Accidentally Turned CCW and the Cocking Piece drops into the Fired Position. Bolt Shims may be installed to Remove Excessive Play between the Bolt Halves when the Bolt is in Battery, giving a More Consistent Seating of the Cartridge. This is a quick video companion to my full length Ruger 77/22 and 77/17 Bolt Shim Installation Video

In this video, I disassemble a Ruger 77/357 and show how to install a VC77TS Volquartsen Target Sear Kit. This Volquartsen Target Sear Kit is available at http://TriggerShims.com Here is the page it is on - https://www.triggershims.com/ruger_m77.html This video also applies to the 77/17, 77/22 and 77/44 This installation will lighten your Trigger Pull - the Easiest Trigger Job for this series rifle. This VC77TS Kit will Reduce Your Trigger Pull to around 2 Pounds by simply changing the Sear and Sear Spring. If this is too light for your hunting rifle, you can keep your factory spring installed to increase Trigger Pull, or install a Wolff Sear Spring. This is a No Gunsmith Required Trigger Job for these rifles, very easy to install with these simple video instructions. Always Safety Check your Rifle after any parts are installed, and if there are any questions regarding safety - see a Qualified Gunsmith. TriggerShims Brand Gun Shims are available for this rifle for the Trigger, Sear and Bolt.

How to Install a http://www.TriggerShims.com​ Brand Shim Kit in a Ruger Double Action Revolver including a SP101, GP100, Redhawk and Ruger Super Redhawk We also Install a Wolff Gunsprings Reduced Power Shooters Pak. TriggerShims Manufactures Hammer and Trigger Shims, Hammer Dog and Cylinder Endshake Shims for Ruger Double Action Revolvers. These Upgrades are used by many Competition Shooters and are Available at http://www.triggershims.com/​ I show how to hone the Shims at 3:40

In this Video, I Install both Hammer Shims and Hammer Dog Shims in a Ruger Super RedHawk Alaskan Revolver in .480 Ruger These parts are available at http://triggershims.com/​ Hammer Shims reduce friction caused by the Hammer Rubbing the Frame Hammer Dog Shims can Improve the Double Action Trigger Pull by keeping the Hammer Dog Properly Aligned. I show the proper way to measure for the Hammer Dog Shims at 8:00​ Minutes in the video. I also Install a Wolff Reduced Power 11 Pound Hammer Spring to reduce the Trigger Pull Weight. The Factory Hammer Spring Rating on this Revolver is 14 Pounds Shively Sales manufactures Gun Shims under the TriggerShims Brand Name.

I Show How to Measure and Install Hammer Shims in a Ruger Double Action Revolver. This includes the Ruger SP101, GP100, Redhawk, Super Redhawk and Alaskan. Installing Shims on both sides of the Hammer will keep it Centered and Will Stop Most of the Scuffing and Scratches on the Hammer from Rubbing Against the Frame. This will also Improve Smoothness of Hammer Operation and Pull, and will give More Reliable Ignition. The same technique is used to measure for Trigger Shims. TriggerShims Brand manufactures Hammer, Trigger, Hammer Dog and Cylinder/Endshake Shims for Ruger Double Action Revolvers, and are available at http://www.TriggerShims.com/​ Hammer Shims are here - http://www.triggershims.com/ruger_dou...​

Hi Folks, Lance here from http://www.TriggerShims.com​ In Part II of this video I show you how to do a Complete Reassembly of a 10/22 Trigger in a Ruger .22 Charger. (Part I is at https://rumble.com/embed/vbcbkx/?pub=1iexq ) We will reinstall all the parts from the Trigger Housing including the Hammer and Main Spring, Magazine Release, Bolt Release, Trigger, Sear and Disconnector, and Safety in a New OEM Metal Trigger and also install a Power Custom Pre-Travel Adjustable Competition Trigger Kit. This kit includes a New Hammer, Adjustable Sear, Titanium Trigger with Over-Travel Stop, 4 Shims, Springs Trigger Pin and Instructions. This drop-in, EDM machined parts kit includes a pre-travel adjustable sear so you can achieve a custom trigger pull that performs exactly to you liking. Matched hammer further helps reduce trigger take-up to ensure a crisp trigger pull for improved accuracy. Includes everything needed to produce a light, crisp trigger for the 10/22: overtravel adjustable titanium trigger, two hammer and two trigger shims, extra power hammer spring, extra power disconnector spring, extra power trigger return spring, sear assembly pin, and trigger pivot pin.

Hi Folks, Lance here from http://www.TriggerShims.com​ In Part I of this video I show you how to do a Complete Disassembly of a 10/22 Trigger. We remove all the parts from the Trigger Housing including the Hammer and Main Spring, Magazine Release, Bolt Release, Trigger, Sear and Disconnector, and Safety. In Part II of this Video we will Reassemble with a New OEM Metal Trigger and a Power Custom Pre-Travel Adjustable Competition Trigger Kit. Drop-in, EDM machined parts kit includes a pre-travel adjustable sear so you can achieve a custom trigger pull that performs exactly to you liking. Matched hammer further helps reduce trigger take-up to ensure a crisp trigger pull for improved accuracy. Includes everything needed to produce a light, crisp trigger for the 10/22: overtravel adjustable titanium trigger, two hammer and two trigger shims, extra power hammer spring, extra power disconnector spring, extra power trigger return spring, sear assembly pin, and trigger pivot pin.

How to Install a Volquartsen Automatic Bolt Release or any Brand of Automatic Bolt Release in a Ruger 10/22 Volquartsen Automatic Bolt Release available at http://www.TriggerShims.com/​

Hi Folks, Lance here from http://www.TriggerShims.com​ In this video, I install a Volquartsen Target Hammer Kit # VC10TH along with a TriggerShims Brand Shims and a Volquartsen # VC10TT in a Thompson Center T/CR22 .22 Rifle Trigger Pull was measured after installation at 2 pounds 2 ounces, a huge improvement. TriggerShims.com Manufacturers Trigger and Hammer Shim Kits This kit is available at http://www.TriggerShims.com/