DIY Car repair

Replaced old worn-out Power Steering Pump. Tools you need: 5/8 " line wrench - https://amzn.to/2jQWwUx Serpentine Belt Tool - https://amzn.to/2lk3JwL Ratchet and socket set - https://amzn.to/2lpW6VL hose clamp pliers - https://amzn.to/2lg8aZl Power Steering Pump, Alternator and AC Pulley Puller & Installer Set - https://amzn.to/3vlFQ6S Disclaimer: Due to factors beyond the control of Hammond Auto LLC, it cannot guarantee against unauthorized modifications of this information or improper use of this information. Hammond Auto LLC assumes no liability for property damage or injury incurred due to any of the information contained in this video. Hammond Auto LLC recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of Hammond Auto LLC, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or the information contained in this video is the user's sole responsibility and not Hammond Auto LLC.

Replacement of rear shocks and front strut assemblies on a 2006 Chevy Trailblazer. Tools you'll need: Torque wrench - https://amzn.to/3tqnbG9 3/8-Inch Drive Deep Impact Socket Set, Metric - https://amzn.to/3ajkoHh 1/2-Inch Drive Deep Impact Socket Set, Metric - https://amzn.to/2QcGqVt Breaker bar Combination Wrench Set - https://amzn.to/3sth1DU Flex-Head Ratcheting Wrench Set, 6-19mm - https://amzn.to/3dp0uwA Ball Pein Hammer 5-pc Set - https://amzn.to/2QdiqRU chisel or flat punch - https://amzn.to/3x5Jtj0 Flathead and Phillips head - https://amzn.to/2QxYSI1 Jack - https://amzn.to/3dqcY7i Jack stands - https://amzn.to/3gj17cL Optional tools: Ball Joint Separator / Fork - https://amzn.to/3uQB2pA 1/2-Inch Impact wrench - https://amzn.to/3mSBb9a Strut Spring Compressor Set - https://amzn.to/3dqTr6M On the passenger side of the SUV/Car 1. Take off the top of the airbox. 2. remove the air tube so you can get access to the two top strut bolts Loosen the two 18mm nuts As an optional step, you can use a set of Strut Spring Compressors to compress the strut to make it easier to pull out the strut. Again this is an optional step. Then use a heavy hammer or Ball Joint Separator / Fork to remove the strut yoke from the lower control arm. Loosen and remove the bolt in the upper part of the yoke. Then separate the split in the yoke with a chisel or flat punch. Be sure to line up the indention on the new strut with the holes of the yoke. Replace the bolt and nut and tighten. Then reverse the steps you did when you removed the strut assemblies For the rear shocks, remove the two 18mm bolts and slide out the shock. To replace reverse those steps. Disclaimer: Due to factors beyond the control of Hammond Auto LLC, it cannot guarantee against unauthorized modifications of this information or improper use of this information. Hammond Auto LLC assumes no liability for property damage or injury incurred due to any of the information contained in this video. Hammond Auto LLC recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of Hammond Auto LLC, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or the information contained in this video is the user's sole responsibility and not Hammond Auto LLC.

Quick video of how to replace the rear light bulbs in a 2006 Chevy Trailblazer. Tools needed: https://amzn.to/3vojlhz OR https://amzn.to/2QVbetN Disclaimer: Due to factors beyond the control of Hammond Auto LLC, it cannot guarantee against unauthorized modifications of this information or improper use of this information. Hammond Auto LLC assumes no liability for property damage or injury incurred due to any of the information contained in this video. Hammond Auto LLC recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of Hammond Auto LLC, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or the information contained in this video is the user's sole responsibility and not Hammond Auto LLC.