EcoWater Birm Iron Filter ETF AIIF9-115 Birm/gravel Replacement
EcoWater Birm Iron Filter ETF AIIF9-115 Birm/gravel Replacement. This video covers disassembly and cleaning tips of the Ecowater birm Iron filter ETF AIIF9-115. Video #2 will cover re-assembly with new gravel, birm and start up. This type of filter removes iron/rust from your water, including the smell and taste. A little background on my own personal dealings with iron in my water, when My wife and I first moved here in 1988 there was a Culligan water softener in our trailer, at that time I knew very little about these things. The softener stopped working, my wife’s hair went from blond to red, and my white socks were orange. In 1991 we built our house and still had the same issue. I searched for information on how to get rid of the iron, I used hole house filters, but the cost of the filters was expensive and really didn’t do a very good job, our softeners would work for a while then not so much, we would then replace it. We tried “Iron Out” in our softener but found out later it wreaks havoc on the softeners resin beads eventually breaking them rendering them useless. Then I found a product called “Crystal Clean” (Link Below), which is made by Terlyn Industries which would clean my softeners resin beads without breaking them so the softener was like new again, but this did not help my original iron problem. I had a friend who worked for Ecowater and he talked about an iron filter, he came and tested our water, we had 20 GPG (grains per gallon) hardness & 6 PPM (parts per million) iron/rust. If I filled a clear glass of water straight from our well, bypassing the softener, set it on the table it looked clear but in 20 minutes you could not see through it, oxygen in the air reacted with the iron/rust in the water and the iron would appear. In 2006 we purchased our Iron filter and had Dale complete the installation for $2500.00 which for us was a lot of money in 2006, especially not knowing if it would work or not. Well I can tell you it was a God send. This filter requires no salt, just a small air compressor that runs when you draw water from a faucet, the oxygen from the pump reacts with the iron/rust particles in the water and iron/rust sticks to the birm like steel to a magnet. Then the filter is set to backflush with water every few days washing the iron/rust particles down a drain. Since the original install in 2006 we had to replace the air pump once, and the birm/gravel change rebuild in 2020 is the only service it has required. I do still run “Crystal Clean” through my water softener every few months just to clean any residual iron/rust that may get through our iron filter; together these two methods have worked very well for us. Good luck! Below are the addresses my YouTube channel which I no longer have access to, my Instagram page, HRI Services welding Facebook page, and my Outdoor Pursuits Facebook page.
https://www.terlyn.com/how-crystal-clean-works/
https://www.doorcounty.com/
https://www.usa.canon.com/
https://www.youtube.com/@HRIservicesllcSturgeonBay
https://www.instagram.com/hri_services/
https://www.facebook.com/HRIServicesllc/
https://www.facebook.com/groups/218766029078898
33
views
Fireplace Ambiance at the Flick of a Switch
Fireplace ambience at the flick of a switch is about building an electric fireplace for any corner, wall or room in your house to give that room the fireplace look without all the bugs, wood chips, chimney fires, etc of a real fireplace on a budget anyone can afford. Below are links to items in the video if you are interested in making one for yourself, these items can also be bought at Menards, Lowes, or Home Depot. Below are the addresses my YouTube channel which I no longer have access to, my Instagram page, HRI Services welding Facebook page, and my Outdoor Pursuits Facebook page.
https://www.amazon.com/AmazonBasics-Extension-Cord-feet-Black/dp/B075BMVZ2N/ref=sr_1_5?ie=UTF8&qid=1548890094&sr=8-5&keywords=10%27+Extension+cord+green
https://www.amazon.com/Design-House-519280-Vanity-Nickel/dp/B00663ZEB0/ref=sr_1_61?ie=UTF8&qid=1548890429&sr=8-61&keywords=3+light+light+fixtures $17.79
https://www.amazon.com/Heritage-Products-Heavy-Steel-Fireplace/dp/B07CSGG3W4/ref=sr_1_2_sspa?ie=UTF8&qid=1548890472&sr=8-2-spons&keywords=fireplace+grate&psc=1
https://www.amazon.com/gp/product/B01N3878K6/ref=ppx_yo_dt_b_asin_title_o00__o00_s00?ie=UTF8&psc=1
https://www.amazon.com/United-Blue-Balsam-Fir-Incense/dp/B07JHF7BX2/ref=sr_1_1_sspa?s=home-garden&ie=UTF8&qid=1548890594&sr=1-1-spons&keywords=fir+incense&psc=1
https://www.amazon.com/s?k=flickering+light+bulbs&crid=3UCRUEPK8FYA5&sprefix=Flicker%2Caps%2C191&ref=nb_sb_ss_ts-doa-p_3_7
https://www.amazon.com/Creative-Hobbies-Flicker-Candelabra-Flickering/dp/B01BI6RZW0/ref=sr_1_7?s=home-garden&ie=UTF8&qid=1548890643&sr=1-7&keywords=Flicker+bulbs
https://www.millerwelds.com/
https://www.doorcounty.com/
https://www.usa.canon.com/
https://www.youtube.com/@HRIservicesllcSturgeonBay
https://www.instagram.com/hri_services/
https://www.facebook.com/HRIServicesllc/
https://www.facebook.com/groups/218766029078898
Brittle Rille - Reunited by Kevin MacLeod is licensed under a Creative Commons Attribution license (https://creativecommons.org/licenses/by/4.0/)
Source: http://incompetech.com/music/royalty-free/index.html?isrc=USUAN1200047
Artist: http://incompetech.com/
23
views
Snowmobile Suspension Stops
This short picture series of aluminum blocks that are for the rear suspension of a snowmobile and were too small to do what the owner wanted them to do which was limit suspension travel so the snowmobile would not lift the skis so high. He wanted the two sides which were created by the factory for use to stay the dimension they were, and wanted me to add approximately ¾” on one side, and 1” on the other side. I had some ¼” x 1” aluminum flat stock and used it as the original block was 1” thick, this being said I had to grind out between each piece so I would get good penetration as I was to mill the welds down to the blocks original thickness which would remove most of the weld. The blocks would not have any kind of stresses on them that would tear them apart just pressure pushing them together. After assembling all the pieces to add to each left and right hand blocks, I had to weld them to the factory blocks and mill them down to size. Below are the addresses my YouTube channel which I no longer have access to, my Instagram page, HRI Services welding Facebook page, and my Outdoor Pursuits Facebook page.
https://www.millerwelds.com/
https://www.doorcounty.com/
https://www.usa.canon.com/
https://www.youtube.com/@HRIservicesllcSturgeonBay
https://www.instagram.com/hri_services/
https://www.facebook.com/HRIServicesllc/
https://www.facebook.com/groups/218766029078898
25
views
V-8 Engine Rebuild SBC #18 Engine Start Up
V-8 Engine Rebuild SBC #18 Engine Start Up, is the twentieth and final video in a series on the full rebuild of the original 350 Chevrolet engine in my 1971 K-10 truck. This video covers the start up of my newly rebuilt small block Chevy.
AC Delco 12TP1E thermostat: https://www.rockauto.com/en/moreinfo.php?pk=4646913&cc=1291766&jsn=1
Airtex AW898HX water pump: https://www.rockauto.com/en/moreinfo.php?pk=4945071&cc=1291766&jsn=2
Energy Suspension engine mounts 31156G: https://www.rockauto.com/en/moreinfo.php?pk=6393681&cc=1291766&jsn=1
AC Delco fuel pump 40987: https://www.rockauto.com/en/moreinfo.php?pk=90446&cc=1291766&jsn=1
Amsoil 20w50 ZROD oil: https://www.amazon.com/AMSOIL-Z-ROD-20W-50-Synthetic-Motor/dp/B009XYKDHY/ref=sr_1_1?keywords=Amsoil+20w50+Zrod&qid=1570310053&sr=8-1
Power Select starter motor: https://www.rockauto.com/en/moreinfo.php?pk=6680640&cc=1291766&jsn=10
Below are the addresses my YouTube channel which I no longer have access to, my Instagram page, HRI Services welding Facebook page, my Outdoor Pursuits Facebook page, and the Classic Chevy Parts page.
https://www.classicchevy.com/
https://www.doorcounty.com/
https://www.usa.canon.com/
https://www.youtube.com/@HRIservicesllcSturgeonBay
https://www.instagram.com/hri_services/
https://www.facebook.com/HRIServicesllc/
https://www.facebook.com/groups/218766029078898
100
views
V-8 Engine Rebuild SBC #17 Clutch & Pressure Plate
V-8 Engine Rebuild SBC #17 Clutch & Pressure Plate, is the nineteenth video in a series on the full rebuild of the original 350 Chevrolet engine in my 1971 K-10 truck. This video covers how to install the Clutch & Pressure Plate on a small block Chevy.
Perfection clutch kit: https://www.rockauto.com/en/moreinfo.php?pk=334258&cc=1291766&jsn=1
Mr Gasket pressure plate bolts: https://www.amazon.com/gp/product/B000BWCFDW/ref=ppx_yo_dt_b_asin_title_o09_s01?ie=UTF8&psc=1
Below are the addresses my YouTube channel which I no longer have access to, my Instagram page, HRI Services welding Facebook page, my Outdoor Pursuits Facebook page, and the Classic Chevy Parts page.
https://www.classicchevy.com/
https://www.doorcounty.com/
https://www.usa.canon.com/
https://www.youtube.com/@HRIservicesllcSturgeonBay
https://www.instagram.com/hri_services/
https://www.facebook.com/HRIServicesllc/
https://www.facebook.com/groups/218766029078898
23
views
V-8 Engine Rebuild SBC #16 Pilot Bushing Replacement
V-8 Engine Rebuild SBC #16 Pilot Bushing Replacement, is the eighteenth video in a series on the full rebuild of the original 350 Chevrolet engine in my 1971 K-10 truck. This video covers how to install the Pilot Bushing on a small block Chevy.
Perfection clutch kit: https://www.rockauto.com/en/moreinfo.php?pk=334258&cc=1291766&jsn=1
Below are the addresses my YouTube channel which I no longer have access to, my Instagram page, HRI Services welding Facebook page, my Outdoor Pursuits Facebook page, and the Classic Chevy Parts page.
https://www.classicchevy.com/
https://www.doorcounty.com/
https://www.usa.canon.com/
https://www.youtube.com/@HRIservicesllcSturgeonBay
https://www.instagram.com/hri_services/
https://www.facebook.com/HRIServicesllc/
https://www.facebook.com/groups/218766029078898
42
views
V-8 Engine Rebuild SBC #15 Distributer Installation
V-8 Engine Rebuild SBC #15 distributer installation, is the seventeenth video in a series on the full rebuild of the original 350 Chevrolet engine in my 1971 K-10 truck. This video covers how to install the distributer on a small block Chevy.
Below are the addresses my YouTube channel which I no longer have access to, my Instagram page, HRI Services welding Facebook page, my Outdoor Pursuits Facebook page, and the Classic Chevy Parts page.
https://www.classicchevy.com/
https://www.doorcounty.com/
https://www.usa.canon.com/
https://www.youtube.com/@HRIservicesllcSturgeonBay
https://www.instagram.com/hri_services/
https://www.facebook.com/HRIServicesllc/
https://www.facebook.com/groups/218766029078898
30
views
V-8 Engine Rebuild SBC #14 Intake Manifold Install
V-8 Engine Rebuild SBC #14 Intake manifold install, is the sixteenth video in a series on the full rebuild of the original 350 Chevrolet engine in my 1971 K-10 truck. This video covers how to install the intake manifold on a small block Chevy.
Fel-Pro full engine gasket set: https://www.amazon.com/gp/product/B01JN5VE7U/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1
Amsoil 20w50 ZROD oil: https://www.amazon.com/AMSOIL-Z-ROD-20W-50-Synthetic-Motor/dp/B009XYKDHY/ref=sr_1_1?keywords=Amsoil+20w50+Zrod&qid=1570310053&sr=8-1
Below are the addresses my YouTube channel which I no longer have access to, my Instagram page, HRI Services welding Facebook page, my Outdoor Pursuits Facebook page, and the Classic Chevy Parts page.
https://www.classicchevy.com/
https://www.doorcounty.com/
https://www.usa.canon.com/
https://www.youtube.com/@HRIservicesllcSturgeonBay
https://www.instagram.com/hri_services/
https://www.facebook.com/HRIServicesllc/
https://www.facebook.com/groups/218766029078898
24
views
V-8 Engine Rebuild SBC #13 180 degrees off?
V-8 Engine Rebuild SBC #13 is your timing 180 degrees off, is the fifteenth video in a series on the full rebuild of the original 350 Chevrolet engine in my 1971 K-10 truck. This video covers how to decipher whether your timing is on or 180 degrees off?
Below are the addresses my YouTube channel which I no longer have access to, my Instagram page, HRI Services welding Facebook page, my Outdoor Pursuits Facebook page, and the Classic Chevy Parts page.
https://www.classicchevy.com/
https://www.doorcounty.com/
https://www.usa.canon.com/
https://www.youtube.com/@HRIservicesllcSturgeonBay
https://www.instagram.com/hri_services/
https://www.facebook.com/HRIServicesllc/
https://www.facebook.com/groups/218766029078898
35
views
V-8 Engine Rebuild SBC #12 Valve Train Install
V-8 Engine Rebuild SBC #12 Valve Train Install is the fourteenth video in a series on the full rebuild of the original 350 Chevrolet engine in my 1971 K-10 truck. This video covers installation of the lifters, pushrods, rocker arms, rocker balls, and rocker nuts.
Engine Pro stage 3 camshaft/lifter kit: https://www.amazon.com/gp/product/B07L7H72LJ/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1
Proform 66905 rockers, balls, & nuts: https://www.amazon.com/gp/product/B000CCDP7G/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1
Below are the addresses my YouTube channel which I no longer have access to, my Instagram page, HRI Services welding Facebook page, my Outdoor Pursuits Facebook page, and the Classic Chevy Parts page.
https://www.classicchevy.com/
https://www.doorcounty.com/
https://www.usa.canon.com/
https://www.youtube.com/@HRIservicesllcSturgeonBay
https://www.instagram.com/hri_services/
https://www.facebook.com/HRIServicesllc/
https://www.facebook.com/groups/218766029078898
26
views
V-8 Engine Rebuild SBC #11 Head Installation
V-8 Engine Rebuild SBC #11 Head Installation is the Thirteenth video in a series on the full rebuild of the original 350 Chevrolet engine in my 1971 K-10 truck. Use a tap and die to chase all the threads and threaded holes in the block and heads. Use a PTFE Teflon type thread sealant on all head bolts as many go through the block into a water jacket which can leak coolant into your oiling system. I used Fel-Pro head gaskets, covers head installation, and torquing of the head bolts.
Permatex Thread Sealant: https://www.amazon.com/gp/product/B000AAJTYS/ref=ppx_yo_dt_b_asin_title_o08_s00?ie=UTF8&psc=1
Fel-Pro full engine gasket set: https://www.amazon.com/gp/product/B01JN5VE7U/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1
Fel-Pro head gasket (Realize these sell each, not a pair): https://www.rockauto.com/en/moreinfo.php?pk=446805&cc=1291766&jsn=1
Fel-Pro VS12869T valve cover gaskets: https://www.rockauto.com/en/moreinfo.php?pk=128425&cc=1291766&jsn=7
Mahle 95094SG exhaust gaskets: https://www.rockauto.com/en/moreinfo.php?pk=3654204&cc=1291766&jsn=1
Below are the addresses my YouTube channel which I no longer have access to, my Instagram page, HRI Services welding Facebook page, my Outdoor Pursuits Facebook page, and the Classic Chevy Parts page.
https://www.classicchevy.com/
https://www.doorcounty.com/
https://www.usa.canon.com/
https://www.youtube.com/@HRIservicesllcSturgeonBay
https://www.instagram.com/hri_services/
https://www.facebook.com/HRIServicesllc/
https://www.facebook.com/groups/218766029078898
46
views
V-8 Engine Rebuild SBC #10 Gaskets
V-8 Engine Rebuild SBC #10 Gaskets is the Twelfth video in a series on the full rebuild of the original 350 Chevrolet engine in my 1971 K-10 truck. Gaskets, gaskets, gaskets, Fel-Pro!
Fel-Pro full engine gasket set: https://www.amazon.com/gp/product/B01JN5VE7U/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1
Fel-Pro head gasket (Realize these sell each, not a pair): https://www.rockauto.com/en/moreinfo.php?pk=446805&cc=1291766&jsn=1
Fel-Pro VS12869T valve cover gaskets: https://www.rockauto.com/en/moreinfo.php?pk=128425&cc=1291766&jsn=7
Mahle 95094SG exhaust gaskets: https://www.rockauto.com/en/moreinfo.php?pk=3654204&cc=1291766&jsn=1
Below are the addresses my YouTube channel which I no longer have access to, my Instagram page, HRI Services welding Facebook page, my Outdoor Pursuits Facebook page, and the Classic Chevy Parts page.
https://www.classicchevy.com/
https://www.doorcounty.com/
https://www.usa.canon.com/
https://www.youtube.com/@HRIservicesllcSturgeonBay
https://www.instagram.com/hri_services/
https://www.facebook.com/HRIServicesllc/
https://www.facebook.com/groups/218766029078898
30
views
V-8 Engine Rebuild SBC #9 Oil Pump & Pan
V-8 Engine Rebuild SBC #9 Oil Pump & Pan is the eleventh video in a series on the full rebuild of the original 350 Chevrolet engine in my 1971 K-10 truck. I cover the installation of a new Melling high volume oil pump, Milodon pan gasket, and Milodon oil pan.
M55HV Melling High volume oil pump: https://www.amazon.com/gp/product/B00C7YMPWS/ref=ppx_yo_dt_b_asin_title_o08_s00?ie=UTF8&psc=1
Milodon 30700 oil pan: https://www.amazon.com/gp/product/B000COU5WM/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1
Milodon 41000 oil pan gasket: https://www.amazon.com/gp/product/B0050VKUV8/ref=ppx_yo_dt_b_asin_title_o09_s01?ie=UTF8&psc=1
Milodon 85000 oil pan bolt kit: https://www.amazon.com/gp/product/B0050VL60M/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1
Below are the addresses my YouTube channel which I no longer have access to, my Instagram page, HRI Services welding Facebook page, my Outdoor Pursuits Facebook page, and the Classic Chevy Parts page.
https://www.classicchevy.com/
https://www.doorcounty.com/
https://www.usa.canon.com/
https://www.youtube.com/@HRIservicesllcSturgeonBay
https://www.instagram.com/hri_services/
https://www.facebook.com/HRIServicesllc/
https://www.facebook.com/groups/218766029078898
28
views
V-8 Engine Rebuild SBC #8 Harmonic Balancer Install
V-8 Engine Rebuild SBC #8 Harmonic Balancer install is the tenth video in a series on the full rebuild of the original 350 Chevrolet engine in my 1971 K-10 truck. I cover the installation of the harmonic balancer that I just installed a new sleeve on; I had then sandblasted the balancer and painted it black. I built the harmonic balancer installation tool that I use in the video. Below are the addresses my YouTube channel which I no longer have access to, my Instagram page, HRI Services welding Facebook page, my Outdoor Pursuits Facebook page, and the Classic Chevy Parts page.
https://www.classicchevy.com/
https://www.doorcounty.com/
https://www.usa.canon.com/
https://www.youtube.com/@HRIservicesllcSturgeonBay
https://www.instagram.com/hri_services/
https://www.facebook.com/HRIServicesllc/
https://www.facebook.com/groups/218766029078898
27
views
V-8 Engine Rebuild SBC #7 Harmonic Balancer Sleeve Install
V-8 Engine Rebuild SBC #7 Harmonic Balancer Sleeve Install is the ninth video in a series on the full rebuild of the original 350 Chevrolet engine in my 1971 K-10 truck. I cover installing a Pioneer harmonic balancer sleeve onto my harmonic balancer to prevent oil leakage caused by the seal working a groove into the factory harmonic balancer.
Pioneer HB4121 harmonic balancer sleeve: https://www.amazon.com/gp/product/B000C625OQ/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1
Below are the addresses my YouTube channel which I no longer have access to, my Instagram page, HRI Services welding Facebook page, my Outdoor Pursuits Facebook page, and the Classic Chevy Parts page.
https://www.classicchevy.com/
https://www.doorcounty.com/
https://www.usa.canon.com/
https://www.youtube.com/@HRIservicesllcSturgeonBay
https://www.instagram.com/hri_services/
https://www.facebook.com/HRIServicesllc/
https://www.facebook.com/groups/218766029078898
41
views
V-8 Engine Rebuild SBC #6 Timing Cover Install
V-8 Engine Rebuild SBC #6 Timing Cover Install is the eighth video in a series on the full rebuild of the original 350 Chevrolet engine in my 1971 K-10 truck. I cover Verification of the timing marks and installation of the timing cover.
Moroso 38590 timing cover bolt kit: https://www.amazon.com/gp/product/B000CONYNY/ref=ppx_yo_dt_b_asin_title_o05_s00?ie=UTF8&psc=1
Milodon 65501 timing cover: https://www.amazon.com/gp/product/B0050VKW7U/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1
Pete Jackson Gear Drive: https://www.amazon.com/PRW-0135001-Noisy-262-400-1955-95/dp/B004BTEJLM
Below are the addresses my YouTube channel which I no longer have access to, my Instagram page, HRI Services welding Facebook page, my Outdoor Pursuits Facebook page, and the Classic Chevy Parts page.
https://www.classicchevy.com/
https://www.doorcounty.com/
https://www.usa.canon.com/
https://www.youtube.com/@HRIservicesllcSturgeonBay
https://www.instagram.com/hri_services/
https://www.facebook.com/HRIServicesllc/
https://www.facebook.com/groups/218766029078898
46
views
V-8 Engine Rebuild SBC #5 Camshaft & Timing
V-8 Engine Rebuild SBC #5 Camshaft & Timing is the seventh video in a series on the full rebuild of the original 350 Chevrolet engine in my 1971 K-10 truck. I cover the installation of a new hydraulic camshaft, a Pete Jackson Gear drive unit and setting the timing of the engine. Below are the addresses my YouTube channel which I no longer have access to, my Instagram page, HRI Services welding Facebook page, my Outdoor Pursuits Facebook page, and the Classic Chevy Parts page.
https://www.classicchevy.com/
https://www.doorcounty.com/
https://www.usa.canon.com/
https://www.youtube.com/@HRIservicesllcSturgeonBay
https://www.instagram.com/hri_services/
https://www.facebook.com/HRIServicesllc/
https://www.facebook.com/groups/218766029078898
37
views
V-8 Engine Rebuild SBC #4 Part 3 Rod Bearing Install
V-8 Engine Rebuild SBC #4 Part 3 Rod Bearing Install is the fifth video and part 3 in a series on the full rebuild of the original 350 Chevrolet engine in my 1971 K-10 truck. I cover the piston installation, Clevite 77 bearing installation the use of Plastigage to measure bearing clearances, how to install the pistons with the ring compressor, how to take bearing caps off, and some on what not to do. Below are the addresses my YouTube channel which I no longer have access to, my Instagram page, HRI Services welding Facebook page, my Outdoor Pursuits Facebook page, and the Classic Chevy Parts page.
https://www.classicchevy.com/
https://www.doorcounty.com/
https://www.usa.canon.com/
https://www.youtube.com/@HRIservicesllcSturgeonBay
https://www.instagram.com/hri_services/
https://www.facebook.com/HRIServicesllc/
https://www.facebook.com/groups/218766029078898
48
views
V-8 Engine Rebuild SBC #4 Part 2 Rod Bearing Install
V-8 Engine Rebuild SBC #4 Part 2 Rod Bearing Install is the fourth video and part 2 in a series on the full rebuild of the original 350 Chevrolet engine in my 1971 K-10 truck. I cover the piston installation, Clevite 77 bearing installation the use of Plastigage, to measure bearing clearance. Below are the addresses my YouTube channel which I no longer have access to, my Instagram page, HRI Services welding Facebook page, my Outdoor Pursuits Facebook page, and the Classic Chevy Parts page.
https://www.classicchevy.com/
https://www.doorcounty.com/
https://www.usa.canon.com/
https://www.youtube.com/@HRIservicesllcSturgeonBay
https://www.instagram.com/hri_services/
https://www.facebook.com/HRIServicesllc/
https://www.facebook.com/groups/218766029078898
43
views
V-8 Engine Rebuild SBC #4 Part 1 Piston & Rod Install
V-8 Engine Rebuild SBC #4 Part 1 Piston & Rod Install is the fourth video and part 1 in a series on the full rebuild of the original 350 Chevrolet engine in my 1971 K-10 truck. I cover the piston ring orientation, ring compressor usage, and piston installation. Below are the addresses my YouTube channel which I no longer have access to, my Instagram page, HRI Services welding Facebook page, my Outdoor Pursuits Facebook page, and the Classic Chevy Parts page.
https://www.classicchevy.com/
https://www.doorcounty.com/
https://www.usa.canon.com/
https://www.youtube.com/@HRIservicesllcSturgeonBay
https://www.instagram.com/hri_services/
https://www.facebook.com/HRIServicesllc/
https://www.facebook.com/groups/218766029078898
47
views
V-8 Engine Rebuild SBC #3 Piston Ring Install
V-8 Engine Rebuild SBC #3 Piston Ring Install is the third video in a series on the full rebuild of the original 350 Chevrolet engine in my 1971 K-10 truck. I cover checking piston side clearance, piston, ring end gap, piston ring side clearance, and installation of the piston rings on the piston prior to installation in the engine block.
Below are the addresses my YouTube channel which I no longer have access to, my Instagram page, HRI Services welding Facebook page, my Outdoor Pursuits Facebook page, and the Classic Chevy Parts page.
https://www.classicchevy.com/
https://www.doorcounty.com/
https://www.usa.canon.com/
https://www.youtube.com/@HRIservicesllcSturgeonBay
https://www.instagram.com/hri_services/
https://www.facebook.com/HRIServicesllc/
https://www.facebook.com/groups/218766029078898
47
views
V-8 Engine Rebuild SBC #2 Crank Install
V-8 Engine Rebuild SBC #2 Crank Install is the second video in a series on the full rebuild of the original 350 Chevrolet engine in my 1971 K-10 truck. This specific video covers a couple of engine specific books, a Chilton repair manual 1972-1980, and How to Hotrod Small Block Chevys. Then I cover the crankshaft installation and use of plasti-gauge to verify the bearing clearances, using plasti-gauge is a second verification that proves my micrometer readings were correct. The two book links are below, I do not have an affiliation with Amazon so I do not get any kick backs so buy them wherever you’d like.
Chiltons GM cars 64-88 = https://www.amazon.com/Chilton-Company-28440-Repair-Manual/dp/B000CFIOZG/ref=sr_1_2?keywords=Chiltons+auto+repair+manual+1972-1980+chevrolet&qid=1569460478&sr=8-2
How to Hotrod Small Block Chevys = https://www.amazon.com/How-Hotrod-Small-Block-Chevys-Engines/dp/0912656069/ref=sr_1_1?crid=NDE2HD3IR9SU&keywords=how+to+hotrod+small-block+chevys&qid=1569460593&sprefix=How+to+hotrod%2Caps%2C348&sr=8-1
Below are the addresses my YouTube channel which I no longer have access to, my Instagram page, HRI Services welding Facebook page, my Outdoor Pursuits Facebook page, and the Classic Chevy Parts page.
https://www.classicchevy.com/
https://www.doorcounty.com/
https://www.usa.canon.com/
https://www.youtube.com/@HRIservicesllcSturgeonBay
https://www.instagram.com/hri_services/
https://www.facebook.com/HRIServicesllc/
https://www.facebook.com/groups/218766029078898
93
views
V-8 Engine Rebuild Small Block Chevy #1
V-8 Engine Rebuild Small Block Chevy #1 is the first video in a series on the full rebuild of the original 350 Chevrolet engine in my 1971 K-10 truck. This specific video covers what you need to think about, like RPM’s you want maximum HP, books you can buy with gobs of great information, things you need to take notice of in disassembly, and things you need to do prior to reassembly. The three book links are below, I do not have an affiliation with Amazon so I do not get any kick backs so buy them wherever you’d like.
Two Stroke performance tuning book = https://www.amazon.com/Two-Stroke-Performance-Tuning-Bell/dp/1859606199/ref=sr_1_1?crid=UMAGK2AAN9OK&keywords=two+stroke+performance+tuning&qid=1569292064&s=gateway&sprefix=Two+stroke+performance%2Caps%2C239&sr=8-1
Four stroke performance tuning book = https://www.amazon.com/Four-Stroke-Performance-Tuning-Graham-Bell/dp/0857331256/ref=sr_1_1?crid=8IBAKAZZCCW2&keywords=four+stroke+performance+tuning&qid=1569292172&s=gateway&sprefix=Four+stroke+performance+tuning%2Caps%2C266&sr=8-1
How to Hotrod Small Block Chevys = https://www.amazon.com/How-Hotrod-Small-Block-Chevys-Engines/dp/0912656069/ref=sr_1_1?crid=1L5PRRFHJY49U&keywords=how+to+hot+rod+small+block+chevys&qid=1677693851&sprefix=how+to+hot+rod+small+block+chevys%2Caps%2C191&sr=8-1
Below are the addresses my YouTube channel which I no longer have access to, my Instagram page, HRI Services welding Facebook page, my Outdoor Pursuits Facebook page, and the Classic Chevy Parts page.
https://www.classicchevy.com/
https://www.doorcounty.com/
https://www.usa.canon.com/
https://www.youtube.com/@HRIservicesllcSturgeonBay
https://www.instagram.com/hri_services/
https://www.facebook.com/HRIServicesllc/
https://www.facebook.com/groups/218766029078898
86
views
V-8 Engine Rebuild Time Lapse 13 Hours in Under 2 Minutes
V-8 Engine Rebuild Time Lapse 13 Hours in Under 2 Minutes, rebuild of my original 350 Chevrolet engine in my 1971 K-10 truck. To see the full length video series of twenty videos see this playlist.
Below are the addresses my YouTube channel which I no longer have access to, my Instagram page, HRI Services welding Facebook page, my Outdoor Pursuits Facebook page, and the Classic Chevy Parts page.
https://www.classicchevy.com/
https://www.doorcounty.com/
https://www.usa.canon.com/
https://www.youtube.com/@HRIservicesllcSturgeonBay
https://www.instagram.com/hri_services/
https://www.facebook.com/HRIServicesllc/
https://www.facebook.com/groups/218766029078898
24
views