Updated RGB Thin Line Flag video

I felt the other video lacked some editing skill so I decided to refine it and streamline it. Level out the audio levels and cut out some of the fat. Hope you enjoy!

This is a how to on how to build the RGB Epoxy Thin line flag. I tried thinking of everything you could need and placing it in this list. Links added for convenience and they help support the channel. Those without links were not available and can be found at your local hardware store.

If you make and sell or make videos for these please credit DissectingDIY

Looking to support the channel please subscribe as I push to get to 1000 subscribers. Also you can click and purchase from the links below:
Patreon:
https://www.patreon.com/join/Dissectingdiy

Amazon Wish list:
https://www.amazon.com/hz/wishlist/ls/Z9J63H04O9OY?ref_=wl_share

-You will spend about 100 on lumber. 1x10x 10’
Finished plywood 1/2 to 3/4 inch about 40 to 50 a sheet
-Epoxy I figured would work best is 1 gallon kit 59.99
-Stains are about 15 a piece. Charred wood accelerator and white 30
-Black paint semigloss 12.00
-Poly matte finish quart about 13.99
-LED lights 18.99
-1” 1/4 fine drywall screws about 7.99
-Sponge brushes
-Paint brushes
-TYVEK tape (2) 30 dollars.
-Epoxy mix cups 16oz pack of 100
About 42 dollar
-32 Oz pack of 100 mix cups
42 dollars
-Rags: 20
-Box of tack clothes 13.99
About 400 just in materials and misc. if you need tools it’s more.

What you Will need.
1x10 at 12' long Or 8 1x2 at 8 feet long

4'x4' of half inch to 3/4 inch finsihed plywood. This project uses a 3/4 inch finished poplar.

(1 quart)Varathane Charred wood accelerator -Water based
(1 quart) Varathane Tintable stain white.
(1 quart) Varathane Water based Poly Matte finish: https://amzn.to/37cnt9H
(1 quart) Black Semi gloss paint.

Stain Sponge: https://amzn.to/39ku1G6

(1) Titebond Extnend: https://amzn.to/3m9Imc9
(1) Wood Glue Applicator: https://amzn.to/33mMxtL
(Box) of tack cloths: https://amzn.to/3md35eZ

Torch: Mapp gas preferred for popping bubbles: Recommend buying at hardware store. expensive on Amazon: https://amzn.to/3nZxUEC

Dremel:
Dremel Tool Kit: https://amzn.to/366rLjH
Dremel Flex Shaft: https://amzn.to/33nHU2C
Dremel Engraving kit: https://amzn.to/2V3r2JV
Dremel Plunge Router: https://amzn.to/3m5Nr54
Dremel Blower attachment: https://amzn.to/3l8xPwn

LED Lighting Strip: https://amzn.to/39fjXhD

Solder kit: https://amzn.to/37fDmwp

LED connector kit: https://amzn.to/3664DSu

Led power extension cable: https://amzn.to/3lal4l0

Koogle 9 Piece Stencil Stars: https://amzn.to/367DJcQ

For Mold:
(2 rolls) Tyvek Tape: https://amzn.to/39knw5Z
1x2 pine strips.
Finished plywood:
Coat all surfaces with tyvek tape

Epoxy
Deep Pour Option:
Large Kit: https://amzn.to/3fBF2E9
Small Kit: https://amzn.to/3pYu6oV
Cost Savings
1/4 inch faster cure option: https://amzn.to/3fBnfwT

White Dye used: https://amzn.to/37qUQGf

Mixing Paddle: https://amzn.to/3q73vWz

Thermometer: https://amzn.to/2VctEF7

Mixing Cups
Small: https://amzn.to/33mZpzQ
16oz: 39w3HZV
32oz: https://amzn.to/2J25gE3

You will need 10 Clamps of greater than 12"
Table Saw: https://amzn.to/3mctbi7
Drill: https://amzn.to/33gDx9m
Driver bit set: https://amzn.to/3lak5Bk
Miter Saw: https://amzn.to/3qcfCSz
Hand Router: https://amzn.to/2JfaU5J
Drill bit kit: https://amzn.to/3q3zuXE

1/2 inch Key hole bit set: https://amzn.to/2JbK7qW

(Box) 1 1/4 drywall screws

Youtube Pages that helped me. Please give them visit:

John Builds it
https://youtu.be/HQYqe_zzeM4

Blue line woodworks:
https://youtu.be/Ef7Un5yW5Ec

Epoxy work: Modustrial maker
https://youtu.be/ru9WPB8K3CM