Premium Only Content

How to Cerakote at Home - Part 2- Applying and Curing Cerakote
This is part 2 of the "How to Cerakote at Home" series. In this video I cover the Cerakote mixing, spraying and curing. Part 1 covers surface preparation for Cerakoting.
Part 1:
https://rumble.com/v6kd8op-how-to-cerakote-at-home-part-1-surface-preparation-for-cerakoting.html
Here are affiliate links to some of the items I use or talk about in the video series:
Master G33 Airbrush https://amzn.to/3sUqqpa
Alternative Spray Gun for Large volume or areas
Paasch HG-08 https://amzn.to/3mmP2Vb
Compressed Air Regulator: https://amzn.to/3rYvFCW
Compressed Air Filter: https://amzn.to/3wtCTCq
Part 1 Items:
Small Blast Cabinet: https://amzn.to/31J8AcX
Handheld Alternative to Blast Cabinet https://amzn.to/39FIDiJ
100 Grit Aluminum Oxide https://amzn.to/3cOJb7L
120 Grit Aluminum Oxide Media https://amzn.to/3wpiKxi
8 Mil Nitrile Gloves https://amzn.to/2Px9S8h
Condensed Cerakoting Guide:
Phase One - Disassemble the item you'll be degreasing
Phase Two - Degrease Acetone is the method described here but other degreasing agents and techniques can be used. Handle the parts with gloves after this to keep from contaminating them
Phase Three - Surface Prep Blast with 100 or 120 grit media, aluminum oxide is my preference
Phase Four - Rack and mask. If any masking is required, now is the time to do that. Racking consists of hanging the parts with wire so they can be Cerakoted and painted.
Phase Five - Gas Out. Bake the metallic parts in an oven at 300 degrees F for an hour to remove any water and bring any residual oils to the surface. If any are found, repeat steps two and three and gas out again.
Phase Six - Prep the H-Series coating. Ratios of hardener to paint are:
- 24:1 Matte Finish
- 18:1 Satin Finish (I generally use 19:1 for a slightly flatter Satin) Note that Cerakote recommends only using 18:1 for their elite series of coatings.
- 12:1 Semi Gloss
I typically use 19:1 which gives my a slightly flatter finish than satin, Strain the coating through a 100 Mesh strainer
Phase Seven - Spraying, I do most of my Cerakoting with an airbrush. Currently using a Master brush G33 but will be upgrading to an Iawata soon. The key is spray an even coat and avoid dry spray which would cause a rough finish. Use a .8mm tip for your airbrush or spray gun
Phase Eight - Curing, Cerakote recommends one of two schedules to cure
Normal Cure - 2 hours at 250 degrees F
Fast Cure - 1 hour at 300 degrees F
00:00 Introduction
00:35 Phase Six - Mixing the Cerakote
03:10 Mesh Straining the Cerakote
03:54 Applying the Cerakote
07:34 Curing the Cerakote
#Cerakote
#Cerakoting
#CeramicCoating
Link to download Cerakote Training Manual:
https://images.nicindustries.com/cerakote/documents/120/h-series-cerakote-elite-training-manual-dt20200115005711425.pdf
-
4:14
The Rubin Report
1 day agoDave Rubin Shares Behind-the-Scenes Story of What Charlie Kirk Did for Him
69.2K57 -
1:58:58
Badlands Media
1 day agoDevolution Power Hour Ep. 389: Psyops, Patsies, and the Information War
110K165 -
2:13:55
Tundra Tactical
11 hours ago $16.45 earnedTundra Talks New Guns and Remembers Charlie Kirk On The Worlds Okayest Gun Show Tundra Nation Live
54.3K13 -
1:45:08
DDayCobra
12 hours ago $43.11 earnedDemocrats Caught LYING Again About Charlie Kirk's KILLER
90.9K100 -
19:23
DeVory Darkins
14 hours ago $21.59 earnedShocking Update Released Regarding Shooter's Roommate as Democrats Issue Insane Response
73.4K183 -
19:53
Stephen Gardner
16 hours ago🔥EXPOSED: Charlie Kirk Shooter's Trans Partner Tells FBI EVERYTHING!
85.7K353 -
2:47:25
BlackDiamondGunsandGear
12 hours agoAfter Hours Armory / RIP Charlie Kirk / What we know
60.6K8 -
29:09
Afshin Rattansi's Going Underground
2 days agoThe Political Life of Malcolm X: Busting the Myths (Prof. Kehinde Andrews)
64.1K17 -
2:47:25
DLDAfterDark
12 hours ago $7.83 earnedThe Assassination of Charlie Kirk - Just What We KNOW
40.2K9 -
1:33:56
MattMorseTV
13 hours ago $44.30 earned🔴Exposing his PARTNER IN CRIME.🔴
92.9K299