House Battery and Solar for the 4Runner - Assembled
1st generation Toyota 4Runner, upgrading the power system in the rear of the truck with a 100AH LiFePO4 battery, 20 amp charge controller and 200W solar panel.
With the battery and charge controller installed, I found I didn't have as much vertical clearance as I originally planned. I think this was mainly due to not accounting for the thickness of the steel angle and clearance for the battery in the cage. Had to shrink my battery connections down in height and allow for more rotation to put them in the best orientation. I wanted the circuit breaker to be attached directly to the positive battery terminal for safety. The battery does have a 100A BMS inside that'll cut off above 100A.
I've already re-routed the PV and DC load cables out the back instead of to the side like I had them in the video. Will also shorten the battery cables and I may actually eliminate the extended connection off the breaker and just pre-wire in the positive battery cable to clean up the wiring and also to better protect that wire by putting it as far back as possible.
All the pieces of angle were cut to fit around the battery with 45* cuts on the top and bottom trays and straight 90* cuts for the rest. I used some 1/8"x1" flat bar for the back bottom and sides (so the battery could slide in). The top was a piece of 1/8" x 2" flat bar. I cut clearance notches in that bar to allow the battery terminals to fit under as well as some notches on the upper angle to clear those terminals as well. You can find that sort off steel at most hardware stores or from a supplier like McMaster-Carr or Metal Supermarkets. This is similar to the cage I built to hold my dual batteries many years ago. I welded that cage up at my evening welding class.
This whole cage is designed to fit entirely on top of the wheel well and inside the opening in the factory roll bar. This will keep these components safely out of the way of things moving around in the bed while traversing bumpy 4WD trails and washboard roads. In the past, I used to bring my Harbor Freight jump start pack and always had trouble securing it in back. This new house battery will not be moving anywhere!
Why this charge controller? A few reasons, main one was the size, it fit in the space available. The other reasons were it had a decent feature set, MPPT, 20 amp rating to handle the 200W panel, Lithium and User charging profiles, built-in BlueTooth. HoboTech did a good review on these: https://youtu.be/HySgUYqjmo8?si=QcVw6jD4AhfpRae1
Why not use a commercial "solar generator"? Two main reasons, main one is that I couldn't find anything that would fit the space I had. Second reason was reliability, I have no experience with those systems but it seems that if one part goes out, the whole unit is dead. With the setup I've designed, if the LiFePO4 battery or BMS quits, I can reconfigure the charge controller to use the lead acid batteries. If the charge controller quits, I can use the alternator to charge the LiFePO4 battery, but this will always be in parallel with 1 or both lead acid batteries. I'll run some tests later to determine if a DC-DC charger will be needed for this of it my high output Premier Power Welder alternator can handle this task. When I'm 100 miles from nowhere and something quits, I like to have options to work around the failed item.
Following videos will get into the roof top solar panel mount...
List of parts used:
LiTime Mini 100AH battery:
https://www.litime.com/products/litime-12v-100ah-mini-lifepo4-lithium-battery-upgraded-100a-bms-max-1280wh-energy
https://amzn.to/3QmxcC5
HQST 20A MPPT Charge Controller
https://hqst.refr.cc/rogerb
https://amzn.to/3S5zhnf
200W AllPowers flexible solar panel:
https://amzn.to/46z7Eax
SAE Extension cable, used 3 ft. and 6 ft. cables:
https://amzn.to/46VnLix
SAE bulkhead connector:
https://amzn.to/3tuP7h1
8 circuit power distribution block:
https://amzn.to/45Ia9pL
#4Runner #softtop #lithiumbatteries #solarpanel #chargecontroller #LiTimestory
-
4:47
4Crawler
8 months agoHouse Battery and Solar for the 4Runner - Adding the Charge Controller
26 -
31:58
City Prepping
1 year agoHow To Build A Solar Setup (12V, 2000W): COMPLETE Step-by-Step, DIY Guide
1.1K1 -
22:39
EPro - Electric Pro Academy
1 year agoInstalling Solar Without Ruining A Historic Home
412 -
17:44
DIY wind solar energy and more
2 years agoDependable Solar Battery, Rolls Surrette GC2 235 AH
175 -
10:01
MotoCheez
1 year agoDaranener Portable Power Station NEO300, 268.8Wh LiFePO4 300W Solar Generator 110V Pure Sine Wave
36 -
3:37
SolarGenerator
9 months agoRUNHOOD Rallye 1200 Plus Portable Power Station 1296Wh Solar Generator
62 -
30:21
EPro - Electric Pro Academy
2 years agoInstalling Residential Solar In One Day
84 -
4:06
SolarGenerator
8 months ago $0.06 earnedFoxthorn igo 3600 Portable Power Station 2500W Solar Generator For Home Outdoor Camping RV Emergency
127 -
12:53
TheDoItYourselfWorld
9 years agoServicing An Old Forklift Battery For Home Solar Power PT II
86 -
7:57
DaveAndSonya
2 years agoHow to Build a Truck Toolbox with Storage Drawers! (Part 15) - Mounting the Solar and Electrical!
36