Premium Only Content

Very Beautiful and New Kurti Neck Design Cutting and Stitching
Certainly! I can provide you with a general description of a beautiful and new kurti neck design, along with cutting and stitching instructions. Please keep in mind that it's always recommended to consult a professional tailor or designer for accurate measurements and precise execution. Here's a popular kurti neck design called the "Keyhole Neckline" that you may find attractive:
Materials:
- Fabric of your choice
- Matching thread
- Scissors
- Measuring tape
- Pins
- Sewing machine or needle
Instructions:
1. Measurements and Cutting:
- Measure the circumference of your neck and add an extra inch for ease and seam allowance.
- Decide how deep you want the keyhole opening to be and mark the center point on the fabric's neckline.
- Measure and mark the desired width of the keyhole, centered on the previous mark.
- From the center of the keyhole, measure and mark the desired length of the keyhole.
- Extend the keyhole marks vertically to the desired depth of the neck cut.
- Cut along the marked lines.
2. Finishing the Raw Edges:
- Fold the raw edges of the keyhole and neckline inside by about ¼ inch and press with an iron.
- Fold the raw edges again by another ¼ inch, press, and pin in place.
- Sew a straight stitch close to the folded edge to secure the hem.
3. Creating the Keyhole:
- Fold the fabric along the vertical lines of the keyhole, right sides together.
- Pin the folded edges together.
- Starting from the top of the keyhole, sew a straight stitch along the vertical lines, ending at the bottom.
4. Neckline Binding:
- Cut a strip of fabric for the binding, approximately 2 inches wide and long enough to go around the neckline.
- Place the binding strip on the neckline, right sides together, aligning the raw edges.
- Pin the binding strip in place, stretching it slightly to fit around the curves.
- Starting from the back of the neckline, sew a straight stitch along the raw edges, attaching the binding to the neckline.
- Trim any excess fabric.
5. Finishing:
- Fold the binding strip over to the wrong side of the fabric, encasing the raw edges.
- Press the folded binding.
- Sew a straight stitch close to the inner folded edge of the binding to secure it in place.
Once you've completed these steps, your kurti with a keyhole neckline should be ready! Remember to customize the design and measurements based on your preferences.
-
9:16
Zoufry
20 hours ago $0.03 earnedThe Evil Design of Mcdonald's Drive Thru
16 -
1:57:28
Gary Cardone
1 day ago $0.33 earnedLIVE With Gary Cardone
1.77K1 -
8:01
MattMorseTV
18 hours ago $10.81 earnedTrump just DROPPED a BOMBSHELL.
66.4K77 -
LIVE
FyrBorne
10 hours ago🔴Warzone M&K Sniping: Is The Overlook OP or Bait?
430 watching -
2:00:53
MG Show
21 hours agoTrump Stops the Epstein Nonsense & Exposes FAKE MAGA; Victory Lap
94.6K75 -
39:21
MattGaetz
1 day agoThe Anchormen Show with Matt Gaetz | Feeding the Dragon
34.8K25 -
6:01
Michael Button
2 days ago $3.64 earnedMy History Degree Lied About Lost Civilizations
46.6K13 -
9:36
MattMorseTV
1 day ago $5.71 earnedThe EU just FOUND OUT.
31.9K51 -
22:39
Forrest Galante
1 day agoPrivate Tour of Australia's Craziest Zoo
167K14 -
6:57:31
ABNERDAGREAT
10 hours ago🔴DISCORD VC/MUSIC ZELDA BREATH OF THE WILD SWITCH 2 EDITION🔴
18.4K1