⚠ Easy Test - 3D Printer Calibration - Extruder Calibration Calculator - E Steps Calculator
⚠ Easy Test - 3D Printer Calibration - Extruder Calibration Calculator - E Steps Calculator
🔴 Subscribe to my channel: https://www.youtube.com/@3DParts4U
🎁 My Patreon page: https://www.patreon.com/3DParts4U
🎧 My Spotify playlists: https://open.spotify.com/user/schipperrene?si=06d90570db5f48f6
A quick 3D printer extruder calibration test!
See if your printer pushes out enough, too much or too little filament.
Send the following 3-line G-code to your 3D printer (SD card or USB drive):
>>
T0 ; Select left extruder
M109 S180 ; Set temperature and wait for left extruder
G1 E100 F150
<<
G1: a linear movement
E100: an extrusion of 100mm length of filament
F150: speed is 150mm per minute
👉 More about G-codes: https://marlinfw.org/docs/gcode/G000-G001.html
👉 Image used: https://unsplash.com/photos/pAATRR5q30A
👉 Image used: https://unsplash.com/photos/Q1NS-nISNIw
My steps per mm were set on 147 and that was the right number.
What if it wasn't the right number?
I added a marker at 100mm from the inlet and it stopped exactly there.
So it extruded 100mm as intended with the g-code.
What if it stopped 10mm before it? Then it extruded 100-10 = 90mm instead of 100mm.
The steps per mm (E-steps) should be 147*100 = 14700 / 90 = 163,3 instead of 147.
Repeat the steps above until 100mm length of filament is extruded after sending the code.
⏱ Chapters:
0:01 Extruder calibration
1:33 Channel promo (https://www.youtube.com/@allvisuals4u)
1:38 Website promo (https://www.3dpartsforyou.com)
👍 Thanks for watching the video Easy Test - 3D Printer Calibration - Extruder Calibration Calculator - E Steps Calculator
🌐 Visit my website: https://www.3dpartsforyou.com
🔩 Subscribe to my other channel AllVisuals4U | Design & Engineering: https://www.youtube.com/@AllVisuals4U
🔩 All playlists of AllVisuals4U | Design & Engineering: https://www.youtube.com/@AllVisuals4U/playlists
📦 Subscribe to my channel 3DParts4U | 3D Printing For Everyone: https://www.youtube.com/@3dparts4u
📦 All playlists of 3DParts4U | 3D Printing For Everyone: https://www.youtube.com/@3dparts4u/playlists
⚡ Subscribe to my short format channel: https://www.youtube.com/@AllVisuals4UShorts
⚡ All playlists of the short format channel: https://www.youtube.com/@AllVisuals4UShorts/playlists
#3DParts4U #AllVisuals4U #3DPrinted #3DPrinting #3DPrints #3DPrint #3DPrinter
#3DPrintedModels #3DModel #PLA #3DDesign #Maker #Making #Modeling #Filament #Tutorial #Tutorials #HowTo #Wiki #Manual #Help #Tips #Tricks #Calibration #ExtruderCalibration #Calculator #ESteps
🔈 Nu Disco Funk by WinnieTheMoog
Free download: https://filmmusic.io/song/6169-nu-disco-funk
Licensed under CC BY 4.0: https://filmmusic.io/standard-license
-
LIVE
The Kirk Minihane Show
2 hours agoKMS LIVE - May 3, 2024
949 watching -
57:28
The Osbournes Podcast
3 days ago $0.24 earnedOur Biggest Fears! Being Watched by a Duck
1.9K12 -
1:39:08
The Podcast of the Lotus Eaters
5 hours agoThe Podcast of the Lotus Eaters #907
9.84K13 -
1:35:57
Crain and Company
3 hours agoGeorgia's Biggest SEC Threat in 2024 (Guest Tim Brando)
5.21K -
17:02
PARAGRAPHIC
22 hours agoThe Oldest American Wheat is Coming Back | PARAGRAPHIC
9.38K13 -
7:02
Morgonn
22 hours agoDating Advice from COLLEGE STUDENTS??? Only Fans? Trans-Women? TELL ALL!!!
21.6K58 -
22:59
JoBlo Originals
17 hours agoWhat Happened To Indiana Jones And The Dial Of Destiny?!
23.7K10 -
1:21:42
MTNTOUGH Fitness Lab
1 day agoCliff Gray: Escaping the 9 to 5 and Thriving in the Backcountry
25.6K1 -
9:03
Adam Does Movies
1 day agoBoy Kills World Movie Review - Too Quirky For Mainstream Audiences?
30.6K1 -
16:36
Misha Petrov
17 hours agoINSANE Protestors Are Taking Over College Campuses
15.9K57