This component adapter can be purchased from Retro-teck here: https://www.ebay.com/str/retroteck - The XBHDA Component Adapter revision passes the brightness and contrast tests. The final results are on par with or slightly better than those of the previous version. - I compared the brightness/contrast slide to the results of the previous test battery. The peak brightness appears to be slightly improved. Though it is very hard to see, even when super zoomed in. Thus you may not be able to tell from normal viewing distances. The contrast is also on par with the previous version. - The optical audio output is clean. - This adapter continues to be the top option for the original Xbox. It also pairs very well with the RetroTink 4K. - The physical design of the adapter itself is also much improved. Its new form factor has all the component and optical outputs facing the same side. The opposite side has the input HD15 connector. - The 3D printed casing also feels improved over previous version. The trimmings for outputs are cut to allow for thicker-jacketed optical cables. - I highly recommend the XBHDA Component Adapter, especially this revision. - Note: The previous version was my top pick of all component adapter options. Combining it with a RetroTink scaler continues to produce far superior results than any direct-to-HDMI adapter. The XBHDA Component Adapter retains its title of being the best external solution. - Side-note: The previous test videos used the RetroTink 5X-Pro for testing. This one used the RetroTink 4K Pro. - Transparency note: The XBHDA Component Adapter was provided to me by Retro-teck for review and demonstration. All findings in this review are from my own testing and observations. Equipment used for this demonstration: Scaler: RetroTink 4K Pro (FW v1.9.6) Profile: Xbox 16-9 DAR - Sharp & Xbox 4-3 DAR - Sharp by cha0shacker Cable (video): HD Retrovision male-to-male Cable (audio): Sys. Concept Toslink to Toslink Premium Optical Cable (T2TXMetal-X) Component Adapter: Retro-teck XBHDA Component Adapter (Revised) Capture Card: TUF GAMING CAPTURE BOX-4KPRO Recorder: OBS Studio Video Editor: Clipchamp (unedited footage, stitched clips together only) Recorded resolution: 1080p **Re-upload note: I have taken down the previous version of this video. It was using a previous firmware version that had a few glitches that skewed the results. This issue has since been resolved, thus I remade the video using FW v1.9.6.

Another short follow-up to the previous component comparison videos. This one compares the Xbox2Wii adapter to the XBHDA adapter from Retro-teck: https://www.ebay.com/str/retroteck Original video here: https://rumble.com/v31mkxm-xbox-component-adapter-video-comparison.html Second video here: https://rumble.com/v33gmrz-xbox-component-video-comparison-2-read-description.html This comparison is to take a look at the Xbox2Wii adapter and compare it to the XBHDA. XBDHA was selected for the comparison as it outdoes the original Xbox HD Pack and is equal to XEDUSA's Component out. Included are some direct side-by-side comparison footage from Crazy Taxy 3 and Dead or Alive 3. I also included some extended test footage of each from Dead or Alive 3 at the end. Which adapter's audio that is playing is indicated with the speaker symbol. Few notes: Brightness Test: All four options pass the brightness test. All four also have the same peak blackness level. However, both the XBHDA, XEDUSA's component out. and Xbox2Wii, each have a better contrast ratio and a higher peak brightness & peak white than the Official HD Pack. The XBHDA & XEDUSA component out appear to be on par with one another in this regard. The Xbox2Wii's peak white is very slightly darker than the other two. But the difference is not directly noticable. Analog Audio Out: None of them have any buzz or hum issues on their analog audio. Any possible noise on the audio would only be heard on high end headphones and loud volume when no other sound is playing (such as a loading screen). Cables used: The first three were all tested with HD Retrovision's Male-To-Male Component cable. The Xbox2Wii adapter used HD Retrovision's Wii Component Cable. All other testing conditions were kept the same for each test.

This is an audio & video comparison of major direct HDMI adapter solutions for the original Xbox. And below is a text review for each adapter. Games used for this comparison: The Suffering (for brightness and contrast check) Crazy Taxi 3: High Roller Dead or Alive 3 Included in this review: Chimeric Systems HDMI Adapter Xbox2HDMI by Electron Shephard LLC https://electron-shepherd.com/collections/featured-collection/products/xbox2hdmi XEDUSA by Beharbros: https://www.beharbros.com/product-page/xedusa-plus HDMI Cable for Original Xbox by LevelHike Hyperkin Panorama HD Cable (Officially Licensed) Testing conditions were the same for each in this video. OBS settings were not changed and used the same equipment for each. With one exception, the Hyperkin has its own permanently attached HDMI cable. Everything else used the same cable. Chimeric Systems: This unit is currently unavailable at the time of this writing. Hopefully they'll be able to return, in the meantime please pray for their family. Passes brightness test Contrast between brighter whites seem to wash out as you can't see the grading on the far right of the scale. Audio test is good. Xbox2HDMI: Has noticeable jail bars. Passes brightness test. One note is if your TV's HDMI Black Level or Color Space is set to auto it may be picking Low or Limited. You'll want to manually change it to Normal or Full. The peak bright and dark appear good enough to support darker games. However, they're both appear brighter than they should. Trying Low/Limited doesn't fix this issue. Contrast is better on Normal/Full. The brighter whites also wash out similar to the Chimeric Systems adapter. Xbox2HDMI is considered a viable option if the caveats above are not an issue for you. XEDUSA: Failed the brightness test. The HDMI output of this device is overly dark. Beharbros suggested to try switching the color space to limited. But the option for it is unavailable with the XEDUSA. I also tried setting OBS settings to Limited and it did not make an improvement. Not recommended to use XEDUSA's HDMI out. However, its component out option does work well, but there is a cheaper component adapter option that yields equal results. See my component comparison for details: https://rumble.com/v31mkxm-xbox-component-adapter-video-comparison.html LevelHike: Fails brightness test Noticeable picture noise Audio has loud hum (more noticeable when quiet) Not recommended. Hyperkin: Fails Brightness Test Noticeable picture noise Significant audio buzz Not recommended. There are a handful of other options out there, but they seem to all be cheap junk that will perform even worse than LevelHike or Hyperkin. If you indeed just want a quick cheap solution despite expected issues, LevelHike seems to be the better of the two cheap options. Chimeric Systems still seems to be the most ideal plug-n-play solution, but given it is unavailable, the Xbox2HDMI would be good middle choice for the time being. Side note: These solutions can cause issues for capture cards when the game first boots or switches between the dashboard and a game (essentially when the Xbox changes resolutions). Its recommended to boot the game before starting capture. Ultimately, if you want the best, I recommend using either the XBHDA Component Adapter or XEDUSA's Component Output with the RetroTink 5X-Pro for best results. Albeit it takes some setting up. As a bonus that solution is stable for capture cards if set to Triple Buffer.

A quick follow-up to the previous comparison video. **Another update video here that adds comparison to the Xbox2Wii adapter **: https://rumble.com/v3h797o-xbox-component-adapter-comparison-3.html Original video here: https://rumble.com/v31mkxm-xbox-component-adapter-video-comparison.html Taking a closer look to how the XEDUSA's component out compares to the XBHDA adapter from Retro-teck: https://www.ebay.com/str/retroteck This has a direct side-by-side comparison of the two. I also indicate which adapter's audio is playing with the speaker symbol. Few notes: Brightness Test: All three options pass the brightness test. All three also have the same peak blackness level. However, both the XBHDA & XEDUSA component out, each have a better contrast ratio and a higher peak brightness than the Official HD Pack. The XBHDA & XEDUSA component out appear to be on par with one another in this regard. (Please note: this assessment only applies to XEDUSA's component output, NOT the HDMI output. XEDUSA's HDMI output fails the brightness test and is noticably darker than other plug-n-play HDMI solutions). Analog Audio Out: None of them have any buzz or hum issues on their analog audio. They each have the same level of noise that cannot be heard during normal play (if using high-end headphones at a very loud volume, you may be able to hear the noise when no audio is playing, such as a loading screen).

This is quick comparison video of three HD component adapter options for the original Xbox. Each test uses the same equipment and settings. **Follow-up video** here: https://rumble.com/v33gmrz-xbox-component-video-comparison-2-read-description.html **Second follow-up that adds comparison to the Xbox2Wii adapter ** here: https://rumble.com/v3h797o-xbox-component-adapter-comparison-3.html Items tested: 1. XBHDA Component Adapter from Retro-teck: https://www.ebay.com/str/retroteck 2. Official Xbox High Definition AV Pack 3. Beharbros XEDUSA Component Out (original version that is no longer sold. New variant: https://www.beharbros.com/product-page/xedusa-plus ) Cable: HD Retrovision Male-To-Male Scaler: RetroTink 5X-Pro Capture: Elgato HD60 S+ Recording Software: OBS Studio Edit Software: Microsoft Clipchamp RetroTink settings used (also my recommended settings for Xbox): Output Resolution 1080p (Under) Horizontal Sampling Preset Generic 16:9 Scaling/Cropping H Position -64 (-80) V Position -7 (17) H (Interp) Size +9% (2267) V Size +9% (1046) H Crop Start (176) H Crop End (2099) V Crop Start (24) V Crop End (1103) HDMI Output V-Sync Frame Lock VRR FreeSync OBS Studio settings used: Recording Format: MKV Video Encoder: NVIDIA NVENC H.264 Audio Encoder: FFmpeg AAC Rate Control: CQP CQ Level: 14 Keyframe Interval: 2 s Preset: P7: Slowest (Best Quality) Tuning: High Quality Multipass Mode: Two Passes (Quarter Resolution) Profile: High Look-ahead: Off Psycho Visual Tuning: On Max B-frames 2 Exported to 1080p MP4 format from Clipchamp.