Making Big RC Car with Foam Board : Datsun 240z (DIY Challenge)

Save
4 years ago
85

The first 1,000 people to use this link will get a 1 month free trial of Skillshare:
https://skl.sh/juliusperdanapaperreplikarcprojects08211

I'm trying something new again this time, trying to build an RC car that I never do it before. I know the hardest RC model to make is model car, but it turned out to be a lot harder than I expected. There were many troubles on the process like, I had to change the gear ratio combination because the first one was too heavy for the motor. The second gear combination was okay but still not efficient. The first motor (1200kv) was burned out, I had to replace it with 650kv. The second gear combination broke their teeth and then I replace the material from PVC foamboard to 2mm plywood, each gear comprise of 4 sheets bonded together. The mechanism was to noisy until I applied lubrication to the gears. And then the steering servo broke I had to replace it with a new one. It's so frustrated I kicked the car few times in madness lol, but luckly it still has it shape. Beautiful shape actually, the back side I think I nailed it, but the front side not so much, because the front tip is supposed to be lower but the front wheel are on the way. After many troubles, finally on the last day it can run and I can RC-drive it as you can see on the video and it turned out quite a good sight. I learned so much on this project that I can use that experience for other future projects like, making gears, use 2 switches to reverse brushless rotation.

SUBSCRIBE and Like to support this channel
#rccar #datsun240z #diyrccar

You can download the plans on the link below :
A4 Plans : https://paper-replika.com/RCplans/PR_Datsun_240z.pdf
A0 Plans : https://paper-replika.com/RCplans/PR_Datsun_240z_A0.pdf
A3 Decal : https://paper-replika.com/RCplans/decal_datsun_240Z.pdf

Build instructions :
https://paper-replika.com/index.php/rc-foam-project/datsun-240z-rc-car-diy

DONATE via Paypal : [email protected]

Join this channel to support me even more:
https://www.youtube.com/channel/UC64lnLfKm09f13iayaCOX0A/join

Playlist :
00:00 Intro
00:45 Making wheels
03:45 Chassis
06:36 Car Body
11:26 Lighting and Detail
14:05 Test Drive
16:26 Review

Specs :
1. Length : 1030mm / 40.5 inches
2. Width : 455mm / 17.9 inches
3. Wheel : 160mm / 6.3 inches
4. Wheelbase : 610mm / 24 inches
5. Weight : 2840 grams/ 100.1 oz
6. Drivetrain : Rear-wheel drive

Electronics
- 3536 1200kv - 650kv Brushless motor
- 50A ESC
- Battery Lipo 3S 2200mah
- 1x Standard servo
- 4x 9 gram servo (micro)
- 20x 5mm blinking LED (yellow)
- 2x 12v LED single LED (white)
- 50 cm 12v LED stripes (white)
- 3v Step down
- 7x limit switch (micro)

Materials :
1. 3mm + 5mm Foamboard/ Depron/ Polyfoam
2. 3mm Plywood / PVC foam board
3. 0.5mm Mica Plastic
4. hot glue, UHU glue, CA glue
5. packing tape/ Oracal 651

Tools :
1. Hot glue gun https://amzn.to/3BXwfGs
2. Heat gun https://amzn.to/3lawF5H
3. Covering iron https://amzn.to/3k2kM2s

Loading 1 comment...