Ender 5 S1 Enclosure - Installation & Testing Using ABS

1 year ago
55

Let's see if this enclosure from Creality for the new Ender 5 S1 lives up to the hype and isn't just a lot of hot air. The Ender 5 S1 is ready to print at 300c right out of the box, but with the right enclosure it'll be able to tackle even the toughest 3D printing challenges!

Enclosure Options:
Acrylic Enclosure for Ender-5 S1 https://bit.ly/Ender-5-S1-Enclosure
Soft Tent Enclosure - https://amzn.to/3GMXwkj
Other 3D Printer Enclosure - https://bit.ly/Creality-3D-Printer-Enclosure

3D Printer:
Creality Ender-5 S1 - https://bit.ly/Creality-Ender-5-S1
Creality Ender-5 S1 - Amazon - https://amzn.to/3YcHFCg

Nozzles:
Micro Swiss Brass Plated Wear Resistant Nozzle - https://amzn.to/3CuDnwG

Helpful Printer Upgrades:
PEI Spring Steel Magnetic Plate Double Side Smooth and Textured - https://amzn.to/3XdPDcV

3D Files:
HexScraper - Printbed scraper - https://www.printables.com/model/122894-hexscraper-printbed-scraper

The Torture Toaster - https://www.printables.com/model/60985-the-torture-toaster

3d Printer Filament That I Use:
PolyLite ABS - https://bit.ly/PolyLite-ABS
PolyLite ASA - https://bit.ly/PolyLite-ASA
PolyFlex TPU 95 (Flexable) - https://bit.ly/PolyFlex-TPU-95
PolyLite Silk PLA Blue - https://bit.ly/PolyLiteSilkPLABlue
NylonX Filament - https://bit.ly/MatterHackersNylonX
PolyTerra Marble PLA - https://bit.ly/PolyTerraMarblePLA
TECSONAR Tricolor PLA - https://amzn.to/3H79d5N
Build Series PLA - https://bit.ly/MatterHackersBuildSeriesPLA
Build Series Silky PLA - https://bit.ly/BuildSeriesSilkyPLAMatterHackers
Build Series ABS - https://bit.ly/MatterHackersBuildSeriesABS
Build Series PETG - https://bit.ly/MatterHackersBuildSeriesPETG
PRO Series Filament - https://bit.ly/MatterHackersPROSeriesFilament

Amazon 3D Printing Filament:
PLA - https://amzn.to/3gsLE9Z
PETG - https://amzn.to/3pXjjvu
ABS - https://amzn.to/3wsTRjS
ASA - https://amzn.to/2RX8dtM
Polycarbonate - https://amzn.to/3cLdr38
Nylon - https://amzn.to/3iNGeI2
________________________________________________
Note : Most of the links that I use that go to products are affiliate link. This means I make a small commission on anything that you happen buy using them. This is at no extra charge to you and this helps support the work I do on this channel. 😁👍
________________________________________________
#creality #ender5 #ender5s1 #3dPrinting #3dScanning #DIY #3DPrinterEnclosure #Ender5S1 #Creality #CrealityEnder5 #Ender5Enclosure #Ender5Installation #Ender5Setup

Loading comments...