How to fix if a printer Won't turn On [4 Easy Steps] [HP, Brother , Canon, Epson]

Source:https://www.technicalsquad.net/tech/what-to-do-when-the-hp-printer-keeps-turning-off/Show more

How to fix if a printer Won't turn On [4 Steps]

If your printer won't turn on, there are a few things you can try. First, check to make sure that the printer is properly plugged into an outlet. Next, check to see if there is a power switch on the printer that needs to be turned on. If neither of these solutions work, you may need to contact the printer's manufacturer for further assistance

Why wont my printer turn on?
1. The power cable is loose
If you find that the power cord to your printer is loose, there are a few things you can do to fix it. First, make sure that the cord is plugged into a surge protector or power strip. If it's not, plug it in and see if that solves the problem. If the cord is already plugged into a power strip, try plugging it directly into the wall outlet.

If neither of these solutions work, the next step is to check the cord itself. If you see any frayed or damaged wires, you'll need to replace the cord. You can usually find replacement power cords at your local electronics store.

Once you've replaced the power cord, your printer should be good as new!
2. Some printer services are not working
If you're having trouble with your HP printer's spoiler services not working, you're not alone. Many users have reported this problem, and it can be quite frustrating.

There are a few things you can try to troubleshoot the issue. First, make sure that your printer is connected to the internet and that the spoiler services are turned on in the printer's settings. If that doesn't work, try restarting your printer.

If you're still having trouble, the problem may be with your printer's firmware. You can try updating the firmware to see if that fixes the issue.

If none of these solutions work, you may need to contact printer expert for further assistance
3. You are using a faulty cable
You are using a faulty printer cable. This could be causing your printer to malfunction. Try using a different cable.
You might not know it, but using a faulty or damaged cable with your HP printer can cause a number of problems. From print quality issues to complete printer failure, it's just not worth the risk.

So, what exactly is a damaged cable? Well, it could be a number of things. Maybe the wires are frayed or broken, the connectors are damaged or loosened, or there is simply too much wear and tear. No matter what the issue is, using a damaged cable is just asking for trouble.

If you're not sure if your cable is damaged, it's always best to err on the side of caution and replace it. After all, a new cable is a relatively small investment compared to the cost of a new printer.

So, the next time you go to print something, make sure you're using a original HP printer cable. It could save you a lot of headaches (and money) in the long run.

4. Malware is corrupting printer functions
If your printer has been acting up lately, it could be due to malware. That's right - malware can now target and corrupt printer functions, making it difficult or even impossible to print.

This new type of malware is still fairly rare, but it's important to be aware of it. If you suspect that your printer is infected, the best thing to do is to disconnect it from your network and run a scan. Don't try to remove the malware yourself, as you could end up doing more harm than good.

If you do find malware on your printer, the best course of action is to factory reset it. This will remove all of the malware and restore your printer to its original state. Of course, this means that you'll have to set up your printer again, so make sure you have all the necessary information handy.

While malware affecting printers is still relatively rare, it's important to be aware of it. By taking some simple precautions, you can help to protect your printer from attack.

Timestamp
0:10 – Why wont my printer turn on
0:27 – The power cable is loose
0:40 – Some printer services are not working
0:58 – You are using a faulty cable
1:36 - Conclusion