Building 2 DIY Raised Garden Beds for under $250.

2/5/2022 Building 2 DIY Raised Garden Beds for under $250

Price that I paid for material with discounts with Lowes card:
Roof panels 8' 6 @ $16.13 = $96.78 (20% off)
Pressure treated lumber 12' 4 @ $9.43 = $37.72 (20% off)
Douglas fir lumber 12' 7 @ $7.93 = $55.51 (20% off)
Sharp point 1" roof screws $22.62 (20% off)
3" #10 deck screws $33.23 (5% off)
$245.86
2.5" #9 deck screws had on hand from another project

This is how to make a raised garden bed.
Building raised garden beds out of wood and galvanized roof panels.
First, I measured and cut all the wood and roof panels to size. Each bed consisted of 2-8’ roof panel, 2-4’ roof panel, 4-8’ long boards, 4-4’ long boards, and 10-19” long boards. I started by using the keg jig to put two pocket holes on each side of the 19" long side pieces. The side support pieces were all cut to 19" long and you need 10 total 3 for each long side and 2 for the short sides. Then, I made two sections that were 4 feet long and two sections that were 8 feet long. By taken, 2- 4' pieces and 2- 19" long piece and screwing them together with the 2.5" screws. Next, I put a piece of the galvanized roof panel that I cut in half and attached it with the 1” sharp point roofing screws. Once I made the 2 4' long sides, I did the same thing with the 8' sections. With the 8' section I used 3 of the 19" long side pieces. Attaching the ends first and then finding the exact middle for the final side support. Once these boards were connected I used a 8' section for the long side screwing down with the 1” sharp point screws. After, all of the side were constructed I used the 90 degree clamp to hold a 4' and 8' section together. I used 7- 3" exterior screws to connect the 4' side to the 8' side on each corner.

Equipment and supplies used to build this 4' x 8' raised garden bed:
3- 2-in x 4-in x 8-ft #2 Prime Pressure Treated Lumber
3- 2-in x 4-in x 96-in Douglas Fir Stud
3- 2.16-ft x 8-ft Corrugated Silver Steel Roof Panel
Sharp point roofing screws 1" #9
Exterior wood screws 3.5" #10
Exterior wood screws 2.5" #9
Kreg Pocket Hole Jig K4
Ryobi impact driver
90 Degree Corner Clamp
Bubble level
speed square
Tape measure

Disclaimer: As an Amazon Associate, I earn a small commission from qualifying purchases at no additional cost to you. This helps to fund content creation, and I really appreciate the support.

Kreg jig:https://amzn.to/3tvX2YS
I couldn't find my exact model but this one is close
Pocket hole jig(similar):https://amzn.to/3MKJGyB
Corner clamps 4 pack:https://amzn.to/39pvpK2
New Microphone: https://amzn.to/3J9zIoD
Camera gear: https://amzn.to/3j4qVtB
Tripod: https://amzn.to/3LGxAXc
Barebones Hori Hori: https://amzn.to/35JsIkK

Thanks for watching please think about subscribing, commenting, and liking the video.

Email:
[email protected]

Instagram:
https://www.instagram.com/barchuckin/

Facebook:
https://www.facebook.com/Barchuckin/

Intro and music from iMovie
#raisedgardenbed
#backyardgardening
#gardeningwithbarchuckin
#howtobuildaraisedgardenbed
#commisionsearned

(building raised garden beds,backyard gardening,Raised garden bed,how to build a raised garden bed,raised garden bed,how to build raised garden beds for beginners,raised garden beds designs,how to make raised vegetable garden beds,raised garden bed made from wood and galvanized roof panels,raised garden beds for beginners,DIY,how to make a raised garden bed,Building 2 DIY Raised Garden Beds for under $250,Gardening with Barchuckin,cheap raised garden beds,gardening)