Sheeting and Insulating Interior Walls + Major Leaks | DIY Vintage Truck Camper Renovation Episode 6
After many trials and many errors when resealing the outside of the truck camper I found some major water intrusion issues that needed dealt with. This videos was suppose to be a video of installing new interior walls only, but as usual things to a massive change. Thankfully I was able to resolve the leaks and get back on track to finish the upper bed area with new foam board insulation and new wall sheeting. It is nice knowing that now the walls are properly insulated resulting in less heat loss and propane use during those cold trips!
May The Lord Jesus Bless Yall!!!
16
views
I Lost 3 Weeks Footage so Here is What I Did | DIY Vintage Truck Camper Renovation Episode 5
Well after a very busy end to 2022 and a hard drive failure causing over 3 weeks of footage lost of me fixing the camper up here is the recap as to what all I did. Video uploads will be resuming normally as I can make them. Right now the camper is my main focus and I am really enjoying working on it. After some very testing decisions to pull the entire sides off and redo rotten wood, insulation, and some painting to the best of my ability. I am so thankful and glad I did so because now I know the Ins and Outs of my vintage truck camper. I also now know how to fix these with the help of YouTube and lots of thinking. Finally the cherry on top was I was able to overcome a relatively hard test and get more learning experience.
May The Lord Jesus Bless Yall!!!
26
views
Greasing my 1977 Ford F250 King Pins and Fixing the Loose Steering Situation
Figure I would upload a video working on the 1977 F250. Been meaning to grease all the front end joints a long time ago but never got around to it. I sure am glad I did this now and not later as the king pins and tie rods were very dry and needed grease really bad. Also REALLY glad I was able to get the steering box adjusted in a bit more and really start to make the truck a drivable safe rig.
May The Lord Jesus Bless Ya!!!
13
views
Fixing 2 Old Vintage Lanterns | 1947 DIETZ No.2 Blizzard + P&A Risbon MFG Co. Oil Lamp |
Just a simple video of me fixing and cleaning up to old lanterns I had lying around collecting dust. Figured they would make a cool video.
May The Lord Jesus Bless Ya!!!
9
views
Servicing the Massey 35 Combine's Distributor and Carb + We "Fix" the F140 Head Episode 7
A bit of a more straight forward video of me going through and making sure the spark and fuel delivery will hopefully not give me trouble when the engine is ready to go back in the Abandon Massey 35 Combine. I still have some more cleaning to do on the head that I will not show, I want to get all the rust junk out so the water pump wont get re destroyed. To my surprise for sitting in the elements for who knows how long the Distributor and carb are in decent shape.
May the Lord Jesus Bless Ya!!!
7
views
Cleaning Parts and the Massey 35 Combine's Water Pump Can't Take the 20 Tons! Episode 6
Despite the water pump getting destroyed in its battle with the 20 ton Jack I think we might be able to bring it back to life with new bearings and some brazing. If you don't already know the Press and Jack used in this video can become very dangerous when under heavy loads. Do not attempt what we did in this video, I am not responsible for you being uninformed, I only show my experiences and what I do and don't do but again take it all at your own risk. That aside what a big boom when that jack came out of there! A very good lesson in standing beside the press and wearing safety equipment like safety glasses or a face shield.
-Keep the comments nice Please and Thank You-
May The Lord Jesus Bless Ya!!!
7
views
Firing up the Smoky Briggs 18HP in My 1980s Murray GT Garden Tractor
Does this motor has some problems or what! All in all I really do think a valve is getting stuck open and causing issues. Seeing how the smoke buffs out the Briggs and Stratton's exhaust I would say a valve is not happy, or at least wasn't happy. According to the previous owner I do know this garden tractor had not ran is supposedly 4 years. While that is nothing compared to the GT6000s I think 15 years It sure looks like it has sat longer but hey who knows. Let me know your thoughts on what is going on with the old Murray and what some remedies could be. Maybe it just needs a good heat cycle haha.
May The Lord Jesus Bless Ya!!!
2
views
Starting Demolition and Uncovering Major Issues! | DIY Vintage Truck Camper Renovation Episode 4
When renovating anything it can become very overwhelming to see the path that is before us. The most important thing I find is to remain orderly and when something needs dealt with do it then and there instead of putting it off. Like the left over wood on the walls or the screws sticking out, I could have left those and then would have had to deal with them down the road when I might not have as much time. Instead I dealt with them then and there and now I can check them off my mental list. Make sure yall wear a mask when doing this stuff, the mold is real bad as is but the powder foam and fiberglass is REALLY bad... It's all real bad for you! Save yourself possible years of life and wear some PPE, its easy cheap insurance in the long run.
May The Lord Jesus Bless Ya!!!
10
views
Trying to "Fix" the Major Roof Leaks | DIY Vintage Truck Camper Renovation Episode 3
The Camper strikes again! After some heavy rain knowing that the roof was in subpar condition, I found that of course the old camper was leaking from multiple spots. Thankfully with some warmer weather Lord willing I was able to get up on the roof and seal up the majority of the problem areas. I would like to say that camper roofs are always a maintenance item with long intervals. Super glad that other than the one plastic roof vent I was able to get it weather sealed up top.
May the Lord Jesus Bless ya!!!
12
views
Fixing the Kolher 18HP Engine in the Free Abandon Craftsman GT6000
After many months of sitting waiting for me to install new piston rings in the old Kohler MV18S the Free Craftsman GT6000 finally moves one step closer to being complete and ready to go to work. I know the tech can be kind of boring, but I prefer my videos to have some information in them while still be an entertaining video. I don't remember but I think I installed the Compression ring on the left side with the chamfer facing the wrong way.... woops, not fixing it for now. Stick around to see more content on the Craftsman Garden Tractor and any other adventures I find myself on!
May The Lord Jesus Bless Ya!!!
Kohler Piston Rings purchased on Isavetractors.com (Not affiliated)
18
views
Toro Suzuki 2 Stroke Push Mower Revival | Sounds Like a Chainsaw! |
Yet another mower revival but his time it's a vintage 2 Stroke! Tell you what the quality of this old 1980s Toro mower shows through. Despite the paint being faded as well as some plastic it's really didn't require much effort in terms of hard or complicated work. 2 strokes are cool but they are kind of a pain to mix the fuel, I guess at the end of the day it really is not that bad just cost extra per gallon. Anyhow its mows and is easy to use. Will be a good tool for the collection and work on the farm! Hope you all enjoy the video!
May The Lord Jesus Bless Ya!!!
2
views
Reviving a 1980s Vintage Murray GT Garden Tractor | Almost Work Ready! |
Well Well Well what do we have here? Another Garden Tractor! Figured there was no better way to start back up recording then a good old garden tractor revival and an old Murray at that! Turns out there is not many parts for these Murray's and mine seems to be in decent shape other than the missing deck. We shall continue recording as the Lord allows!
May The Lord Jesus Bless Ya!!!
5
views
Cleaning up Years of Nasty Smoke! | DIY Vintage Truck Camper Renovation Episode 2
Finally got another video up on fixing this old camper. I do have to say I was feeling a bit overwhelmed with this project and really let it get to me for a while but now that I got back to working on it I am SUPER excited for what's in store for this project and the adventures that await. Who knows where it will lead!
To touch on those coins I really want to emphasize the point I was trying to make which is to never get caught up in some worked based religion that leads away from the simple fact that Christs blood was shed for you and me. Someone thought that by reading the text on those coins that they then would get a reward but rather were left empty handed many times wondering if they didn't try hard enough. The Lords perfect free gift of salvation is something that could never be earned by an imperfect creation. Rather accept that if you fully rely on the Lord Jesus as your savior your sins are fully blotted out by the ever so precious blood of the Lord Jesus Christ.
May The Lord Jesus Bless Ya!!!
6
views
Finally Fixing my 1977 Ford F250 Windshield Washer Pump & Tank
Fixing one of the final things I took off the 77 long ago and never got around to for some reason. This video was short as I had expected and Lord willing, I will have some more content out very soon.
Hey if your reading this maybe Drop a Like and Subscribe?... Thanks!
May The Lord Jesus Bless Ya!!!
In Partnership with the eBay Affiliate Program I earn a small commission when you purchase products through the links below no extra charge to you. It helps me out a TON!
(Always Double check your vehicle Parts/Part # Before Purchasing)
(eBay Affiliate Links)
Washer Pump: https://ebay.us/SMLeqP
Washer Pump Connector: https://ebay.us/dA6Wx9
Windshield Wiper Switch: https://ebay.us/EAGI3g
8
views
Reviving Free Garden Tractor + Lawn Mower | Craftsman GT6000 / MTD Yard Machine |
Well yet the start of another adventure! Both of these where Free! This video was filmed around the time of me getting the $300 Lot of stuff and as most of you by now know the MTD Yard Machine with the 20Hp Tecumseh ended up getting traded for my 1950s Massey Harris / Ferguson 35 Combine. You can see that mower all finished and pretty in episode one of the Massey Combine Revival. The Free Vintage Craftsman GT6000 Garden Tractor that has been sitting for 10 years with the Kohler MV18 engine is most likely here to stay, I really like it. I actually liked the Yard Machine as well but as with lots of things in life some things move on to other lives, hopefully the Yard Machine gets treated good but who knows with people and mowers.
From here the channel has a new project, the Craftsman GT6000 Garden Tractor!
May The Lord Jesus Bless Ya!!!
7
views
Seized Pistons in Abandon 1950s Massey Harris 35 Combine Revival Episode 5
What a change of events in the adventure of the Massey Harris / Ferguson Combine revival. Honestly, I did not expect this engine to be in such rough shape for the condition some engine components are in. If I had to guess someone only replaced some things and didn't do a very great job and they for sure didn't EVER do oil changes, when I say the oil was black and dirty it was top 3 worst I have ever seen, like midnight black oil. Anyhow we shall get through it one way or another Lord willing!
May The Lord Jesus Bless Yall!!!
3
views
Seized Engine Removal Abandon 1950s Massey Harris 35 Combine Revival Episode 4
Yet another fast learning and adapting episode to the challenges this Massey keeps throwing but we are getting it done and in good time the right way. I should say that I was really not expecting to do this and have had to learn and soak a lot in brand new information in. That is why my moods tend to fluctuate a bit in the videos but yall know how I film. At the end of the day the Continental F140 came out fairly easy compared to what can happen when equipment lives outside, it could have been WAY worse but the Lords looking out for me haha. Hope you all enjoy another episode of me working on this 1950s Massey Ferguson Harris 35 Combine!
Hey if your reading this maybe Drop a Like and Subscribe?... Thanks!
May The Lord Jesus Bless Yall!!!
2
views
Discovering Bad News in the Abandon 1950s Massey Harris 35 Combine Revival Episode 3
First off sorry for the camera being unstable yall, the new mini tripod I bought is not the best, next video that will be fixed. Other than that I hope you all enjoy this unfortunate and crazy discovery hiding inside the Massey's Continental F140 Engine. Of course I will be fixing this engine because its what I do and I love what I do. When challenges come our way at first it can seem hopeless and overwhelming but I am quickly learning to adapt and overcome and push through. At the end of the day this combine is a HUGE blessing and will teach me a lot much like the 77 f250 did. Hope yall are ready for yet another adventure and journey fixing and Lord willing using this Combine in the future!
Hey if your reading this maybe Drop a Like and Subscribe?... Thanks!
May The Lord Jesus Bless Ya!!!
2
views
Wiring Mess on the Abandon 1950s Massey Harris 35 Combine Revival Episode 2
Some adventures brings things you never knew existed in the world and for me a 6 volt positive ground system is a first. I know how 6 volt systems work but have never messed with one but I for sure did not know there was a system where the ground is positive. Supposedly thought to reduce corrosion, not sure how well it worked but hey and least they tried stuff back then. Now a days everything is all the same old nonsense with more stuff to fail. Also I for sure will be fixing up the wiring in the control panel a bit better as well. A new water temp gauge is needed as the old one has left the building long ago. Hope you all enjoy another episode of me working on this 1950s Massey Ferguson Harris 35 Combine!
Hey if your reading this maybe Drop a Like and Subscribe?... Thanks!
May The Lord Jesus Bless Ya!!!
3
views
I Traded a Free Lawnmower for an Abandon 1950s Massey Harris 35 Combine Episode 1
Well here we go on another crazy adventure, This was something I never ever would have imagined myself owning or even being interested in but man I sure an glad I got it. I am aware that this is not a Super 35 and is just a 35. It needs work and if your reading this be ready in the coming videos, ye old motor is rough.... Well I will leave it at that and let yall enjoy me stumbling through my first experience with farm equipment revivals.
Hey if your reading this maybe Drop a Like and Subscribe?... Thanks!
May The Lord Jesus Bless Ya!!!
2
views
Traveling over 370 Miles to get My Next Project! | DIY Vintage Truck Camper Renovation Episode 1
The interesting things you find when searching the internet for cheap sales. Decided to search further outside my area and ended up buying this old 1978 Caveman Truck Camper for $300 dollars from some interesting fellows to say the least. None the less my Dad and I got the truck camper home on an over 3 hour one way trip. It was an awesome adventure and HUGE thanks to my Dad for helping me out to get this hunk of junk haha. Its rough but I happen to be an expert in dealing with the more ruff projects in life and trust me yall it will come around in due time.
Also this series is not going to be your super edited upbeat videos, I do stuff real time with what I got, just like yall will be doing it, that's how I roll. Anyhow hopefully you all follow along and enjoy the renovation / remodel of this truck camper.
Hey if your reading this maybe Drop a Like and Subscribe?... Thanks!
May The Lord Jesus Bless Ya!!!
16
views
Getting Two 1960s Homelite 2 Stroke Chainsaws Running Again | Homelite C-51 Homelite XL-12 |
Man what a fun and challenging video to make. These saws definitely threw me for a loop but man I wish they took 1960s simplicity and used it in todays products. Always treat chainsaws with respect and never be ill informed when using them. Talk to people and watch lots of videos on proper chainsaw handling. If yall want a full restoration video of these saws ya now what to do!
Hey if your reading this maybe Drop a Like and Subscribe?... Thanks!
May The Lord Jesus Bless Ya!!!
4
views
Reviving an Old Craftsman 2.5Hp Electric Chainsaw | It's Greasy! |
Bringing some different videos to the channel and hopefully yall enjoy. This was a fun little side project and despite the bad weather I got it done. After watching the video back the saw performed way better than before, The electric motor was much quieter and from sharpening the chain it cut WAY faster. For being an old electric chainsaw I am pretty impressed.
Hey if your reading this maybe Drop a Like and Subscribe?... Thanks!
May The Lord Jesus Bless Ya!!!
3
views
I'm Quitting YouTube, Not what you might think
My Website: https://forgivencreation.com/
My Rumble: https://rumble.com/user/ForgivenCreation
My Buy Me a Coffee: https://www.buymeacoffee.com/forgivencr7
I have to Trust Jesus and stand for what I believe in
25
views
2
comments
Finishing up the 1977 Ford F250.... Almost
In this video the f250 gets some final touches furthering its progress almost top being complete... For now. Who knows maybe later on the F250 will come back with some more upgraded parts. Of course if something breaks I will film fixing it but as of right now I have maybe 2 other videos to record on the truck. But for now the channel will be seeing some other types of content, after all I never intended to be restricted to one thing on this channel and never ever want that.
Always on a New Adventure!
May The Lord Jesus Bless Ya!!!
In Partnership with the eBay Affiliate Program I earn a small commission when you purchase products through the links below no extra charge to you. It helps me out a TON!
(Always Double check your vehicle Parts/Part # Before Purchasing)
(eBay Affiliate Links)
11
views