Datsun 510 Stock Exhaust Work (Ep#3)
I go ahead and hook up my stock exhaust so I can get this car back on the road soon. I don't need the cops called on me for a car that has less than 100HP.
5
views
Datsun 510 Clutch Master & Slave Cylinder (Ep#7)
My Datsun started leaking clutch fluid. It was old hardware so I just replaced it for piece of mind. Nice quick little project. Enjoy!
5
views
Datsun 510 Engine & Battery Tray Removal (Ep#8)
This work took place over the better part of a week. I removed the engine and transmission, cleaned up some parts, and removed the battery tray.
18
views
Datsun 510 Radio Install (Ep#6)
I take an older CD player that I had already and install it in the 510! Guess what it shorts out and dies not too long later, so I will be revisiting this at some point
1
view
Datsun 510: Installing Stock Fuel Pump (Ep#4)
In this video I replace the electric fuel pump with the stock pump, that was still attached to the car. It is much quieter, and one of the downsides of the electric is it was hooked up to run when the key was on, not to prime and then shut off.
12
views
Datsun 510 Brake Work (Ep#2)
I replace my master cylinder, rear wheel cylinders, and bleed/flush the entire system
5
views
Datsun 510 Project Intro and Carb Work
In this video I give a brief introduction to the project, and swap the original carb to a Weber Redline downdraft carb.
55
views
1
comment
Datsun 510: Finishing the Car! (Ep#87)
Holy COW! I am done with the car. This is a great feeling!
Car: 1972 Datsun 510
Engine: L20B
Transmission: 280zx 5-Speed
Suspension: TechnoToy Tuning Front and Rear Coilovers
Minor Mods: Battery to Trunk, Electric Fans, Mercedes CLK Seats
Equipment Used in the Videos:
Camera: GoPro Hero7 Black : https://amzn.to/2GrWDxa
Gopro Mic Adapter: https://amzn.to/2WziAkj
Gopro Case that holds the microphone adapter: https://amzn.to/2uBqoWH
Wireless Microphone: https://amzn.to/2JW0gjZ
Soldering and Hot Air Station: https://amzn.to/2YGqeLI
Spot Welder Bit: https://amzn.to/2UuINyT
Blaire Lubricant: https://amzn.to/2VTFfYy
SEM Copper Weld: https://amzn.to/2Dr8V8p
Voice Over: Power Director 17
Editing Software: Power Director 17
Music: By Cullen F: https://soundcloud.com/berial-feilong29?utm_source=clipboard&utm_medium=text&utm_campaign=social_sharing
Build Thread Information:
RATSUN: http://community.ratsun.net/topic/72953-aarons-1972-datsun-510-4-door-glory/page-1
GRM: https://grassrootsmotorsports.com/forum/build-projects-and-project-cars/datsun-510-4-door-project-name-tbd/134878/page1/
Nissan Figaro Window Motor Replacement
I used a 300zx Window Motor Replacement to revive the failed motor in Danielle's Figaro!
5
views
3d Modeled: Compact Socket Box
I really don't love the fact I can't get a cheap set of just Metric sockets so I did what anyone with a 3d printer would do. Designed my own. I will be printing this one after I finish the design let me know what you think in the comments, waste of time, or interesting. The next interation will have integrated socket holding
Voice Over: Power Director 17
Editing Software: Power Director 17
Music: By Cullen F: https://soundcloud.com/berial-feilong29?utm_source=clipboard&utm_medium=text&utm_campaign=social_sharing
14
views
Nissan Figaro Catalytic Converter Delete
We got rid of the old catalytic converter in the Figaro. It seems a bit more peppy. It wasn't the issue with the car though
8
views
Datsun 510: New Exhaust (Ep#86)
I build a new Exhaust, it was tiring work for sure!
00:00 Intro
00:30 Old Exhaust Broken
01:30 Fabrication Series and Taking Lessons
04:00 New Exhaust Components
05:20 Removing the Old Exhaust
09:00 Looking at the Old Exhaust
11:30 Fabricating Down Pipe
14:45 Center Pipe
15:30 Center Pipe Complete (Tack’ed)
19:00 Discussing TIG Welding
20:00 Finishing TIGing the Center
20:45 Sharpening TIG Electrodes
23:30 Rear Portion of Exhaust
26:50 Welding on Rear Exhaust Hanger
29:00 Washer
29:55 Overview of New Exhaust and Comparison to Old
32:00 Installing New Exhaust
32:52 New Exhaust Sound
18
views
Datsun 280z Front Bumper Repair
I welded up the holes and painted the front bumper on the Z.
30
views
1
comment
Datsun 510: Adjusting the Valves (Ep#85)
I decide I should take off the valve cover for the first time just to ensure the valves are properly set.
11
views
Datsun 510: Trans Rebuild Pt 5: Complete! (Ep#84)
In this video I clean up the housing and get it all installed back in the car. I even walk through the process of creating my very own 3d printed clutch alignment tool.
13
views
Datsun 510: 5 Spd Trans Rebuild Pt3 (Ep#82)
I continue to rebuild the transmission. I get 3rd, 4th, 4th counter gear (on and off) in this video.
Car: 1972 Datsun 510
Engine: L20B
Transmission: 280zx 5-Speed
Suspension: TechnoToy Tuning Front and Rear Coilovers
Minor Mods: Battery to Trunk, Electric Fans, Mercedes CLK Seats,
Equipment Used in the Videos:
Camera: GoPro Hero7 Black : https://amzn.to/2GrWDxa
Gopro Mic Adapter: https://amzn.to/2WziAkj
Gopro Case that holds the microphone adapter: https://amzn.to/2uBqoWH
Wireless Microphone: https://amzn.to/2JW0gjZ
Soldering and Hot Air Station: https://amzn.to/2YGqeLI
Spot Welder Bit: https://amzn.to/2UuINyT
Blaire Lubricant: https://amzn.to/2VTFfYy
SEM Copper Weld: https://amzn.to/2Dr8V8p
Voice Over: Power Director 17
Editing Software: Power Director 17
Music: By Andromeda: https://www.reverbnation.com/andromedamusicofficial
Build Thread Information:
RATSUN: http://community.ratsun.net/topic/72953-aarons-1972-datsun-510-4-door-glory/page-1
GRM: https://grassrootsmotorsports.com/forum/build-projects-and-project-cars/datsun-510-4-door-project-name-tbd/134878/page1/
00:00 Intro
01:05 Explaining the work to this point
04:11 Checking 1st Gear Clearance
05:11 Checking 2nd Gear Clearance
06:10 3rd Gear Install
08:11 3rd/4th Synchro Hub, Realization
09:30 Front Counter Gear Removal
12:27 3rd/4th Synchro Hub, Actual Install
14:00 Thinking and Checking
15:56 Input Shaft
17:10 Re-Installing the Front Counter Gear
12
views
Datsun 510: Starting 5-Spd Rebuild (Ep#81)
In this video I start putting the gears, bearings, and shafts back together as the transmission work continues.
00:00 Intro
01:20 Cleaning Center Adapter Plate Surface
03:51 Mainshaft Center Bearing Installation
06: 41 Countershaft Center Bearing Installation
09:11 Bearing Retainer Plate and Reverse Idler Shaft Installation
14:50 Cleaning Bearing and Staking the Plate
17:11 3rd, 2nd, 1st Gear Layout
20:17 2nd Gear Installation
22:20 2nd and 1st Gear Synchronizer Installation
25:45 1st Gear Installation
29:00 Washer, Detent Balls, and Outro
4
views
Datsun 510: Finishing 5-spd Trans Teardown (Ep#80)
Another several days working on this car. The transmission is now apart completely and there still appears to be NOTHING wrong. Spoiler alert I have been driving this car as I am publishing this video in September 2021, when I did the work in February of 2021.
The main work accomplished today is removing all of the gears and bearings from the main shaft and counter shaft of this 280zx 5-spd transmission.
Car: 1972 Datsun 510
Engine: L20B
Transmission: 280zx 5-Speed
Suspension: TechnoToy Tuning Front and Rear Coilovers
Minor Mods: Battery to Trunk, Electric Fans, Mercedes CLK Seats,
Equipment Used in the Videos:
Camera: GoPro Hero7 Black : https://amzn.to/2GrWDxa
Gopro Mic Adapter: https://amzn.to/2WziAkj
Gopro Case that holds the microphone adapter: https://amzn.to/2uBqoWH
Wireless Microphone: https://amzn.to/2JW0gjZ
Soldering and Hot Air Station: https://amzn.to/2YGqeLI
Spot Welder Bit: https://amzn.to/2UuINyT
Blaire Lubricant: https://amzn.to/2VTFfYy
SEM Copper Weld: https://amzn.to/2Dr8V8p
Voice Over: Power Director 17
Editing Software: Power Director 17
Music: By Andromeda: https://www.reverbnation.com/andromedamusicofficial
Build Thread Information:
RATSUN: http://community.ratsun.net/topic/72953-aarons-1972-datsun-510-4-door-glory/page-1
GRM: https://grassrootsmotorsports.com/forum/build-projects-and-project-cars/datsun-510-4-door-project-name-tbd/134878/page1/
Timeline:
00:00 Intro
00:23 Removing Rear Shaft Nut
02:12 Removing 5th Gear Spacer
02:53 Removing 5th Gear Counter Shaft Nut, Bear, and Gear
05:31 Removing 5th Gear
06:55 Removing 5th/Reverse Gear Shift Collar
08:45 Reverse Idler Shaft Work
12:43 Back from the Hydraulic Press / Parts Overview
18:00 Removing First Gear
20:45 Removing 1st and 2nd Shift Collar
23:50 Removing 2nd Gear
24:07 Removing 3rd Gear Input Bearings, 3rd/4th Shift Collar
26:30 Removing Input Shaft Bearing and 4th Gear
30:10 Removing Countershaft Front Bearing
32:20 Identification of all of the Major Parts Removed
50
views
Datsun 280z Time Lapse Road Trip
I went on a trip to Northern Nevada in January of 2021. This is that video. Hope you enjoy, but wouldn't be surprised if you don't. Thanks for watching.
14
views
3d Printed Datsun 510 Tachometer
Seeing a $500 plus tachometer made it very cost prohibitive to have a nice factory looking tachometer in the 510. This project hopes to fix that. I modeled a housing that will accept the cheapest 2" tachometer from Amazon.
1
view
Preview: Datsun 510 2" Tach Adapter 3d Print / Fusion 360
Check it out! I am working on a protoype to integrate a cheap tachometer for the 510. So you can print your own when I finish it. Let me know what you think.
5
views
Datsun 280zx 5-speed Trans Rebuild (Datsun 510 Ep 79)
I got the 5-speed pulled apart. I started doing some of the checks on the transmission.
STOCK INFORMATION IN VIDEOS:
Car: 1972 Datsun 510
Engine: L20B
Transmission: 280zx 5-Speed
Suspension: Rear Coil Overs
Minor Mods: Battery to Trunk, Electric Fans,
Equipment Used in the Videos:
Camera: GoPro Hero7 Black : https://amzn.to/2GrWDxa
Gopro Mic Adapter: https://amzn.to/2WziAkj
Gopro Case that holds the microphone adapter: https://amzn.to/2uBqoWH
Wireless Microphone: https://amzn.to/2JW0gjZ
Soldering and Hot Air Station: https://amzn.to/2YGqeLI
Spot Welder Bit: https://amzn.to/2UuINyT
Blaire Lubricant: https://amzn.to/2VTFfYy
SEM Copper Weld: https://amzn.to/2Dr8V8p
Voice Over: Power Director 17
Editing Software: Power Director 17
Music: By Andromeda: https://www.reverbnation.com/andromedamusicofficial
Build Thread Information:
RATSUN: http://community.ratsun.net/topic/72953-aarons-1972-datsun-510-4-door-glory/page-1
GRM: https://grassrootsmotorsports.com/forum/build-projects-and-project-cars/datsun-510-4-door-project-name-tbd/134878/page1/
55
views
Datsun 510: Removing Transmission (Ep #78)
There is nothing wrong with the transmission. I didn't know that so I pulled it out of the car! In the next several videos in this series I will rebuild the transmission.
Car: 1972 Datsun 510
Engine: L20B
Transmission: 280zx 5-Speed
Suspension: Rear Coil Overs
Minor Mods: Battery to Trunk, Electric Fans,
Equipment Used in the Videos:
Camera: GoPro Hero7 Black : https://amzn.to/2GrWDxa
Gopro Mic Adapter: https://amzn.to/2WziAkj
Gopro Case that holds the microphone adapter: https://amzn.to/2uBqoWH
Wireless Microphone: https://amzn.to/2JW0gjZ
Soldering and Hot Air Station: https://amzn.to/2YGqeLI
Spot Welder Bit: https://amzn.to/2UuINyT
Blaire Lubricant: https://amzn.to/2VTFfYy
SEM Copper Weld: https://amzn.to/2Dr8V8p
Voice Over: Power Director 17
Editing Software: Power Director 17
Music: By Andromeda: https://www.reverbnation.com/andromedamusicofficial
Build Thread Information:
RATSUN: http://community.ratsun.net/topic/72953-aarons-1972-datsun-510-4-door-glory/page-1
GRM: https://grassrootsmotorsports.com/forum/build-projects-and-project-cars/datsun-510-4-door-project-name-tbd/134878/page1/